COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel Association V3

0x8E

3

COMMAND_CLASS_BATTERY

Battery

0x80

1

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Transport Service V2

0x55

2

COMMAND_CLASS_WAKE_UP_V2

Wake Up V2

0x84

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_NOTIFICATION_V8

Notification V8

0x71

8

COMMAND_CLASS_SECURITY_2

Security S2

0x9F

1

COMMAND_CLASS_VERSION_V3

Version V3

0x86

3

COMMAND_CLASS_SUPERVISION

Supervision

0x6C

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Manufacturer Specific V2

0x72

2

COMMAND_CLASS_BASIC_V2

Basic V2

0x20

2

Manual_Primary_Lang

Product or Owner's Manual

Battery Quantity

Battery Type

Color

Communications Protocol

Firmware Updatable

Outdoor Use

Sensors

Supported Notification Types

1

5

0

Lifeline association group Include command class: Battery report, Notification report, and Device Reset Locally notification, Binary report.

2

5

0

Root Device group(Binary Sensor) Binary Sensor Command Class:Compatible with 300 series 1-Binary Sensor reports status of open or close door via Lifeline. 2-When the sensor detects status change between close door and open door, the device will be triggered.

3

5

0

Root Device group(Binary Sensor) Binary Sensor Command Class:Compatible with 300 series 1-Binary Sensor reports the removed status of door sensor. 2-When the sensor detects status change of tamper, the device will be triggered.

4

5

0

Root Device group(Notification) 1-Notification report open door or close status via Lifeline. 2- When the sensor detects status change between close door and open door, the device will be triggered.

5

5

0

Root Device group(Notification) 1-Binary Sensor reports the removed status of door sensor. 2- When the sensor detects status change of tamper, the device will be triggered.

4

Device Wake-Up

- Wake up Notification is transmitted every 24 hours by default. - Wake up Notification is transmitted after Notification Report is transmitted

2

Exclusion

A.) Click the - (Remove) button in your Z-Wave App and follow the further instructions. B.) Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times. The App will show if the Remove device process was successful and the Status-LED on device will flash 6 times. Repeat the exclusion process from step A if it was not successful.

5

Factory Reset

1. Press the Tamper-button 3 times within 1.5 Seconds 2. The device is now restored to factory settings Note: 1, This procedure should only be used if the primary gateway is not capable of acting. 2, If the multi-sensor is set to the factory setting, the status is set to ""not included"", the association settings and possible configurations are reset to default.

1

Inclusion

A.) Slide the base unit from the mounting plate and remove the safety strip from the battery compartment. B.) Click the + (Add) button in your Z-Wave App and follow the further instructions C.) Press the Tamper-button 3 times within 1.5 seconds and the Status-LED on the base unit front will flash 3 times. The App will show if the Add device process was successful and the Status-LED will turn off. Repeat the inclusion process from step B if it was not successful.

Home Security

(Refer to parameters): State idle

Emergency Alarm

(Refer to parameters): State idle

General purpose