COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Firmware Update Meta-Data V4

0x7A

4

COMMAND_CLASS_SCENE_ACTUATOR_CONF

Scene Actuator Conf

0x2C

1

COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_PROTECTION_V2

Protection V2

0x75

2

COMMAND_CLASS_CLOCK

Clock

0x81

1

COMMAND_CLASS_APPLICATION_STATUS

Application Status

0x22

1

COMMAND_CLASS_SWITCH_BINARY

Switch Binary

0x25

1

COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_CONFIGURATION

Configuration

0x70

1

COMMAND_CLASS_SECURITY

Security S0

0x98

1

COMMAND_CLASS_SWITCH_MULTILEVEL_V2

Switch Multilevel V2

0x26

2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Transport Service V2

0x55

2

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_SECURITY_2

Security S2

0x9F

1

COMMAND_CLASS_SWITCH_COLOR

Switch Color

0x33

1

COMMAND_CLASS_SUPERVISION

Supervision

0x6C

1

COMMAND_CLASS_SCENE_ACTIVATION

Scene Activation

0x2B

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Manufacturer Specific V2

0x72

2

COMMAND_CLASS_NOTIFICATION_V4

Notification V4

0x71

4

COMMAND_CLASS_METER_V4

Meter V4

0x32

4

COMMAND_CLASS_SWITCH_BINARY

Switch Binary

0x25

1

COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_SCENE_ACTIVATION

Scene Activation

0x2B

1

COMMAND_CLASS_NOTIFICATION_V4

Notification V4

0x71

4

Manual_Primary_Lang

Product or Owner's Manual

Sensors

Supported Notification Types

Switch Load Capacity Watts

Z-Wave Scene Type

Supported Meter Type

Color

Firmware Updatable

Outdoor Use

1

5

0

Z-Wave Plus Lifeline. *Device Reset Locally Notification: Issued when Factory Reset is performed. *Basic Report: Issued when switch state has changed. *Binary Switch Report: Issued when switch state has changed. *Color Switch Report: Issued when a color component level of the Indicator Light has changed. *Multilevel Switch Report: Issued when the multilevel switch value of the Indicator Light has changed. *Notification Report (Type=0x08; Event=0x06): Issued when over-current detected. *Notification Report (Type=0x08; Event=0x08): Issued when over-load detected. *Notification Report (Type=0x08; Event=0x00): Issued when over-current or over-load is release. *Notification Report (Type=0x09; Event=0x03): Issued when built-in unrecoverable temperature fuse detected the internal temperature exceeds the limit and disconnect. *Meter Report: Issued periodically to report the current Meter reading, and the sending frequency is related to Configuration Parameter 0x6F (111). Issued when the current Power, Power Consumption or Current is over the threshold value.

2

5

0

Retransmit a Basic Set, Binary Switch Set or Scene Activation Set to the nodes associated.

8

Alarm Response

Enabled by (Alarm Settings), and determines what the switch does in the case an alarm is triggered. When receives any alarm enabled by Alarm Settings, Indicator Light will keep blinking based on Parameter 0x12 (18). It will prohibit user from manually or RF control the switch state until the alarm is disable.

0

1

0

0

0

9

Alarm Settings

Determine if alarms are enabled in Switch, and what Switch will react to which alarm. The format of the parameter is Bit field (Checkboxes). The parameter MUST be treated as a bit field where each individual bit can be set or reset. A graphical configuration tool SHOULD present this parameter as a series of checkboxes. Please refer to the manual for more details about supported Notification Type and Notification Event.

0

2

0

0

0

10

Setting to disable alarm

Determines the method of disabling the alarm of the device. Note: Power off will also disable the alarm response without any limitation.

0

2

0

0

0

80

Configure what command will be sent via Lifeline when switch state has changed.

Configure what command will be sent via Lifeline when switch state has changed.

0

1

0

0

2

4

Over-load protection

Define a threshold power and automatically turn off switch when the load connected bypasses the maximum allowed power regardless of always on setting. Over-load protection will be active if the load power exceeds the setting and lasts for more than 30s. If be active, Indicator Light will become red light blinking and the product will send out Notification Report (Over-load detected), and disable the function that manually or RF control the switch state until users set Protection State to be unprotected through the Gateway or Controller. Even power off will still keep Protection State.

0

2

0

0

2415

81

Load Indicator Mode setting.

Note: Configuring brightness and color of Indicator Light in different time/status of different modes will be saved in the current setting mode. Please refer to the manual for more details.

0

1

0

0

2

82

Configure the enable and disable time of Night Light Mode

If you want to set Night Light Mode to be enable at 19:00 at night and disable at 07:30 in the morning, you just need to configure: Value1=0x13, Value2=0x00, Value3=0x07, Value4=0x1E.

0

4

0

0

301991936

91

Threshold Power (W) for inducing automatic report.

Threshold Power (W) for inducing automatic report.

0

2

0

0

0

92

Threshold Power Consumption (kWh) for inducing automatic report.

Threshold Power Consumption (kWh) for inducing automatic report.

0

2

0

0

0

93

Threshold Current (A) for inducing automatic report.

Threshold Current (A) for inducing automatic report.

0

1

0

0

0

111

Configure the sending frequency of Meter Report.

Configure the sending frequency of Meter Report.

0

4

0

0

600

255

Factory Reset or Initialization (Write Only)

Factory Reset or Initialization (Write Only)

0

1

0

0

0

2

Exclusion

1. Set your Z-Wave Controller into its 'Remove Device' mode in order to remove the product from your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step. 2. Make sure the product is powered. If not, plug it into a wall socket and power on. 3. Click Action Button 2 times quickly; it will bright violet light, up to 2s. 4. If Removing fails, it will bright red light for 2s and then turn back to Load Indicator Mode; repeat steps 1 to 3. Contact us for further support if needed. 5. If Removing succeeds, it will become breathing blue light. Now, it is removed from Z-Wave network successfully.

1

Inclusion

This product supports Security 2 Command Class. While a Security S2 enabled Controller is needed in order to fully use the security feature. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. (1) SmartStart Learn Mode SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code present on the product with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity. Indicator Light will become flash white light for 1s indicating the product has been powered, and then become flash blue light indicating SmartStart Learn Mode starts. It will become constantly bright yellow light after being assigned a NodeID. If Adding succeeds, it will bright blue light for 2s and become Load Indicator Mode. If Adding fails, it will bright red light for 2s and turn back to breathing blue light and then start SmartStart Learn Mode again. Note: The label of QR Code on the product and package are used for SmartStart Inclusion. The Z-Wave DSK Code is at bottom of the package. Please do not remove or damage them. (2) Classic Inclusion Learn Mode 1. Set your Z-Wave Controller into its 'Add Device' mode in order to add the product into your Z-Wave system. Refer to the Controller's manual if you are unsure of how to perform this step. 2. Make sure the product is powered. If not, plug it into a wall socket and power on; its LED will be breathing blue light all the time. 3. Click Action Button once, it will quickly flash blue light for 30 seconds until it is added into the network. It will become constantly bright yellow light after being assigned a NodeID. 4. If your Z-Wave Controller supports S2 encryption, enter the first 5 digits of DSK into your Controller's interface if /when requested. The DSK is printed on its housing. 5. If Adding fails, it will bright red light for 2s and then become breathing blue light; repeat steps 1 to 4. Contact us for further support if needed. 6. If Adding succeeds, it will bright blue light for 2s and then turn to Load Indicator Mode. Now, this product is a part of your Z-Wave home control system. You can configure it and its automations via your Z-Wave system; please refer to your software's user guide for precise instructions. Note: If Action Button is clicked again during the Classic Inclusion Learn Mode, the Classic Inclusion Learn Mode will exit. At the same time, Indicator Light will bright red light for 2s, and then become breathing blue light.

5

Factory Reset

If the primary controller is missing or inoperable, you may need to reset the device to factory settings. Make sure the product is powered. If not, plug it into a wall socket and power on. To complete the reset process manually, press and hold the Action Button for at least 15s and then release. The LED indicator will become breathing blue light, which indicates the reset operation is successful. Otherwise, please try again. Contact us for further support if needed. Note: 1. This procedure should only be used when the primary controller is missing or inoperable. 2. Factory Reset will: (a) Remove the product from Z-Wave network; (b) Delete the Association setting; (c) Restore the configuration settings to the default.

6

Additional Special Features

Regardless of the state of the product, when over-current or over-load detected, it will automatically TURN OFF switch and set Local Protection State to be 2 and RF Protection State to be 1, and start red light blinking. Users can’t manually or RF control the switch state until setting the Protection State to be unprotected through the Gateway or Controller, even power off will still keep Protection State.

Electric meter

Import

Electric Meter Consumption

Power Management

(Refer to parameters): State idle

System

(Refer to parameters): State idle

Power

Voltage

Current