COMMAND_CLASS_SCENE_ACTUATOR_CONF

Scene Actuator Conf

0x2C

1

COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_THERMOSTAT_FAN_MODE

Thermostat Fan Mode

0x44

1

COMMAND_CLASS_CLOCK

Clock

0x81

1

COMMAND_CLASS_BATTERY

Battery

0x80

1

COMMAND_CLASS_THERMOSTAT_OPERATING_STATE

Thermostat Operating State

0x42

1

COMMAND_CLASS_THERMOSTAT_MODE

Thermostat Mode

0x40

1

COMMAND_CLASS_THERMOSTAT_FAN_STATE

Thermostat Fan State

0x45

1

COMMAND_CLASS_SENSOR_MULTILEVEL

Sensor Multilevel

0x31

1

COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_CONFIGURATION

Configuration

0x70

1

COMMAND_CLASS_THERMOSTAT_SETPOINT_V2

Thermostat Setpoint V2

0x43

2

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC

Manufacturer Specific

0x72

1

COMMAND_CLASS_SCENE_ACTIVATION

Scene Activation

0x2B

1

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Firmware Update Meta-Data V2

0x7A

2

COMMAND_CLASS_MULTI_CMD

Multi-Command

0x8F

1

COMMAND_CLASS_BASIC

Basic

0x20

1

Manual_Primary_Lang

Product or Owner's Manual

Firmware Updatable

Sensors

Battery Type

Color

Battery Quantity

Thermostat HVAC Systems Supported

Thermostat Modes

Thermostat Power Source

2

5

0

Group 2 Association Alerts will send a BASIC_SET 0xFF when a Cool Call starts and a BASIC_SET 0x00 when the Cool Call ends.

1

5

0

Z-Wave Plus Lifeline Group 1 Association is the default status report channel in Z-Wave+ lifeline requirements. Group 1 Alerts are to notify an associated device of a thermostat generated change. Thermostat generated changes are those changes that originate at or by the thermostat. The following Command Classes can be sent to the lifeline: • BATTERY_REPORT • DEVICE_RESET_LOCALLY_NOTIFICATION • SENSOR_MULTILEVEL_REPORT • THERMOSTAT_SETPOINT_REPORT • THERMOSTAT_SETPOINT_MODE • THERMOSTAT_FANMODE_REPORT • THERMOSTAT_FANSTATE_REPORT • THERMOSTAT_OPERATINGSTATE_REPORT • THERMOSTAT_CONFIGURATION_REPORT

3

5

0

Group 3 Association Alerts will send a BASIC_SET 0xFF when a Heat Call starts and a BASIC_SET 0x00 when the Heat Call ends.

2

Fan Type

Sets the fan type. Electric (Fan w/Heat) or Gas (no Fan w/Heat)

0

1

0

0

0

4

2nd Stage Heat Enable

Enables or disables the second stage heat operation.

0

1

0

0

0

5

Aux Heat Enable

Enables or disables aux heat operation.

0

1

0

0

1

6

2nd Stage Cool Enable

Enables or disables the second stage cool operation.

0

1

0

0

0

7

C/F Type

Enables changing from Centigrade to Fahrenheit or vice versa.

0

1

0

0

1

9

MRT

Sets the Minimum Run Time (MRT) delay before a heating/cooling cycle can turn off. Sets heating/cooling cycle time. Prevents rapid on/off cycling.

0

1

0

0

3

11

H Delta Stage 1 ON

Sets the delta from setpoint that stage 1 heating starts

0

1

0

0

1

17

C Delta Stage 1 ON

Sets the delta from setpoint that stage 1 cooling starts.

0

1

0

0

1

24

Display Lock

Sets locking and unlocking of control of the display screen.

0

1

0

0

0

3

Change Over Type

Sets change over type. Change over with cool or change over with heat.

0

1

0

0

0

55

Cool Timer (hours)

Sets Cool Timer (hours). 0 to 4000.

0

2

0

0

0

61

Fan Purge Heat

Sets Fan Purge Heat. Sets the system blower delay off time after a heat call ends (fan purge). 0 to 90 Seconds.

0

1

0

0

0

62

Fan Purge Cool

Sets Fan Purge Cool. Sets the system blower delay off time after a cool call ends (fan purge). 0 to 90 Seconds

0

1

0

0

0

187

0xBB

Periodic Temperature Send Interval (min). 0=Disabled. 1-120 minutes.

0

1

0

0

0

1

System Type

Sets the system type. Standard or Heat Pump

0

1

0

0

0

8

MOT

Sets the Minimum Off Time (MOT) delay before another heating/cooling cycle can begin. Provides compressor short cycle protection. “Wait” is displayed on screen when active.

0

1

0

0

5

43

Remote Sensor 1 Node Number

Sets remote sensor 1 node number. 0=disabled.

0

1

0

0

0

48

Internal Sensor Temp Offset

Sets Internal Sensor Temp Offset. -7 to 7

0

1

0

0

0

49

R1 Sensor Temp Off set

Sets R1 Sensor Temp Offset. -7 to 7 degrees

0

1

0

0

0

52

Filter Timer (hours)

Sets Filter Timer (hours). 0 to 4000

0

2

0

0

0

53

Filter Timer Max (hrs)

Sets Filter Timer Max (hrs). 0 to 4000.

0

2

0

0

300

186

0xBA

Temperature Delta Autosend Threshold (how many degree change from last autosend). 1 to 5 degrees.

0

1

0

0

2

46

Remote Sensor 1 Temperature

Displays remote sensor 1 Temperature.

0

1

0

0

0

54

Heat Timer (hours)

Sets Heat Timer (hours). 0 to 4000.

0

2

0

0

0

194

RH Delta Autosend Threshold

Sets how often a relative humidity report is sent based on percent change.

0

1

0

0

5

195

Periodic RH Send Interval

Sets how often a relative humidity report is sent based on time. 0=Disabled, 1-120 minutes.

0

1

0

0

0

1

Inclusion

Inclusion is started by putting the controller into add node state and performing the General Programming Procedure. As part of the process, the thermostat sends a node information frame at normal power. Low power inclusion is not possible. General Programming Procedure (for controllers supporting the thermostat device class): 1. Set your primary controller to Include, add or Install mode, to add the thermostat as a node on your network (see your controller’s user manual for detailed instructions). 2. Press any button to take thermostat out of sleep mode. 3. Press and hold FAN button for 5 seconds. SETUP will be displayed in the status display line. 4. Scroll to “Z-Wave” using  buttons. Press SELECT. 5. When prompted by your Z-Wave controller, Press the YES button in the Z-Wave Install screen. 6. Press SELECT (mode button) to add thermostat to network. 7. Display line should fl ash WAIT then SUCCESS if Z-Wave connection is made. 8. If Z-Wave does not connect to controller, WAIT, then FAIL will flash in status display line. 9. If thermostat fails to connect, repeat Steps three (3) thru (7) to re-try connecting. Your controller will indicate the thermostat was successfully added to its network (see your controller’s user manual for details). Also, you can check if the thermostat was successfully added to the network by checking the ZHID (Home ID) and ZNID (Node ID) located in the Thermostat Info screen. For other specific tasks such as adding the thermostat to Scenes or Groups, or deleting the thermostat from an existing network, refer to the Z-Wave controller instructions.

2

Exclusion

Exclusion is started by putting the controller into remove node state and performing the General Programming Procedure. As part of the process, the thermostat sends a node information frame at normal power. Low power exclusion is not possible.

5

Factory Reset

Factory Reset WARNING: Please use this procedure only when the Z-Wave Primary Controller is missing or otherwise inoperable. To reset the TBZ500's Z-Wave parameters to Factory Settings (both Z-Wave and HVAC settings): 1. Remove power from the TBZ500. 2. Power up the TBZ500 and when you see TBZ500 on the screen, hold down the MODE and FAN buttons simultaneously. 3. Release when RESET appears on the Status Line. 4. Once the TBZ500 resets the Z-Wave and HVAC settings, a DONE confirmation message will appear on the screen before the thermostat self-reboots.

6

Additional Special Features

Test Mode - shortens the system built-in delays (like MOT and MRT) Aux Heat Enable (Heat Pump Systems only) - Enables the auxiliary heat operation. 2nd Stage Heat Enable - Enables the second stage heat operation 2nd Stage Cool Enable - Enables the second stage cool operation Minimum run time - Sets the Minimum Run Time (MRT) delay before a heating/cooling cycle can turn off. Prevents rapid on/off cycling. Minimum Off Time - Sets the Minimum Off Time (MOT) delay before another heating/cooling cycle can begin. Provides compressor short cycle protection. “Wait” is displayed on screen when active. Heat Setpoint Max. - Sets the maximum heating setpoint value. Will not ramp or accept setpoints higher than this maximum Cool Setpoint Min. - Sets the maximum heating setpoint value Heat Blower Off Delay - Sets the system blower delay off time after a heat call ends (fan purge) Cool Blower Off Delay - Sets the system blower delay off time after a cool call ends (fan purge) Heat - Cool Delta - Sets the minimum separation between heating and cooling setpoints. Heating Stage 1 on Threshold - Sets the delta from setpoint that stage 1 heating starts. Heating Stage 1 Off Threshold - Sets the delta from setpoint that stage 1 heating stops. Heating Stage 2 On Threshold - Sets the delta from setpoint that stage 2 heating starts. Heating Stage 2 Off Threshold - Sets the delay from setpoint that stage 2 heating stops. Aux Heat On Threshold - Sets the delta from setpoint that stage 3 heating starts. Aux Heat Off Threshold - Sets the delta from setpoint that stage 3 heating stops. Cooling Stage 1 On Threshold - Sets the delta from setpoint that stage 1 cooling starts. Cooling Stage 1 Off Threshold - Sets the delta from setpoint that stage 1 cooling stops. Cooling Stage 2 On Threshold - Sets the delta from setpoint that stage 2 cooling starts. Cooling Stage 2 Off Threshold - Sets the delta from setpoint that stage 2 cooling stops. Restore Defaults - Restores all settings to factory defaults.

Air temperature

Humidity