COMMAND_CLASS_FIRMWARE_UPDATE_MD_V4

Firmware Update Meta-Data V4

0x7A

4

COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_THERMOSTAT_FAN_MODE

Thermostat Fan Mode

0x44

1

COMMAND_CLASS_THERMOSTAT_OPERATING_STATE_V2

Thermostat Operating State V2

0x42

2

COMMAND_CLASS_BATTERY

Battery

0x80

1

COMMAND_CLASS_THERMOSTAT_FAN_STATE

Thermostat Fan State

0x45

1

COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_CONFIGURATION

Configuration

0x70

1

COMMAND_CLASS_SENSOR_MULTILEVEL_V6

Sensor Multilevel V6

0x31

6

COMMAND_CLASS_THERMOSTAT_MODE_V2

Thermostat Mode V2

0x40

2

COMMAND_CLASS_THERMOSTAT_SETPOINT_V2

Thermostat Setpoint V2

0x43

2

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Transport Service V2

0x55

2

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_SECURITY_2

Security S2

0x9F

1

COMMAND_CLASS_SUPERVISION

Supervision

0x6C

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Manufacturer Specific V2

0x72

2

Manual_Primary_Lang

Product or Owner's Manual

Battery Quantity

Battery Type

Thermostat Modes

Thermostat Power Source

Sensors

Thermostat HVAC Systems Supported

1

2

0

Z-Wave Plus Lifeline

4

Thermostat Power Source

The Thermostat Power Source parameter is a read-only status of the thermostat power source.

0

1

0

0

0

5

Humidity Reporting Threshold

The Humidity Reporting Threshold parameter specifies the threshold change in the relative humidity as detected by the thermostat to trigger an unsolicited report when association reporting is enabled.

0

1

0

0

2

9

Thermostat Recovery Mode

The Thermostat Recovery Mode parameter specifies the HVAC recovery mode type.

0

1

0

0

2

10

Temperature Reporting Filter

The Temperature Reporting Filter parameter specifes the upper and lower bounds of the ambient temperature reporting.

0

4

0

0

0

11

Fan Timer

This configuration is used to activate the fan with an automatic shut-off timer.

0

1

0

0

0

1

Temperature Reporting Threshold

The Temperature Reporting Threshold parameter specifies the threshold change in the ambient air temperature as detected by the thermostat to generate an usolicited report when association reporting is enabled.

0

1

0

0

2

3

Utility Lock

The Utility Lock parameter enables or disables the utility lock. If the utility lock is enabled, the thermostat setpoint cannot be modified by the user on the thermostat physical user interface.

0

1

0

0

0

2

HVAC Settings

The HVAC Settings parameter contains a read-only description of the HVAC settings of the thermostat.

0

4

0

0

0

7

Thermostat Swing

The Thermostat Swing Temperature parameter specifies the swing temperature on the thermostat.

0

1

0

0

2

6

Auxiliary Heat

The Auxiliary Heat parameter enables or disables Thermostat Mode called Auxiliary Heating in the thermostat while the thermostat mode is Heat.

0

1

0

0

0

1

Inclusion

Alternative to SmartStart, the thermostat can be added by: 1. Set your primary controller to INCLUDE mode to add the thermostat as a node on your network (see your specific controller’s User Manual for detailed instructions). 2. The thermostat main screen shows a welcome message. Press the SIDE button to continue. 3. Press the SIDE button to initiate the inclusion process. This initiates the network connection process. If inclusion fails, the screen says “Failed”. Press the SIDE button to try adding again. 4. When the thermostat has been successfully included to a Z-Wave network, the screen displays a confirmation. Press the SIDE button to continue. You can now configure the thermostat to work with your HVAC system. 5. Your primary controller should indicate that the thermostat was successfully added to its network (see your specific controller’s User Manual for details).

2

Exclusion

The thermostat can be removed from the Z-Wave network process similar to the inclusion process. Set your primary controller to EXCLUDE.

5

Factory Reset

Reset clears Z-Wave settings and restores Z-Wave settings to factory default. Reset does not affect Thermostat settings. Use this procedure only if the Z-Wave network primary controller is missing or inoperable. The Thermostat automatically resets and reboots the Z-Wave radio. You will need to reconnect the Thermostat to your Z-Wave network.

Air temperature

Humidity