COMMAND_CLASS_CONFIGURATION_V4

Configuration V4

0x70

4

COMMAND_CLASS_SCENE_ACTUATOR_CONF

Scene Actuator Conf

0x2C

1

COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel Association V3

0x8E

3

COMMAND_CLASS_INDICATOR_V3

Indicator V3

0x87

3

COMMAND_CLASS_SECURITY

Security S0

0x98

1

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Transport Service V2

0x55

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Firmware Update Meta-Data V5

0x7A

5

COMMAND_CLASS_SWITCH_MULTILEVEL_V4

Switch Multilevel V4

0x26

4

COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3

Association Group Information V3

0x59

3

COMMAND_CLASS_BASIC_V2

Basic V2

0x20

2

COMMAND_CLASS_SECURITY_2

Security S2

0x9F

1

COMMAND_CLASS_VERSION_V3

Version V3

0x86

3

COMMAND_CLASS_SUPERVISION

Supervision

0x6C

1

COMMAND_CLASS_SCENE_ACTIVATION

Scene Activation

0x2B

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Manufacturer Specific V2

0x72

2

Manual_Primary_Lang

Product Manual

Firmware Updatable

Switch Load Capacity Current

Neutral Wire Required

Z-Wave Scene Type

1

5

0

Lifeline

0x0001

Lifeline association

3

Min Level

Minimum Fan Speed level allowed

2

1

0

99

10

4

Max Level

Maximum Fan Speed level allowed

2

1

0

99

99

7

Locator Status

Locator LED Status

2

1

0

255

255

5

Preset Level

Preset Level for On

2

1

0

99

0

6

Ind Timeout

LED Dim Level Indicator Timeout

2

1

0

255

3

8

Where to find S2 DSK on product

SmartStart enabled products can be added into a Z-Wave network by scanning the Z-Wave QR Code found on the top of the or the back of the box with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on and in the network vicinity. The QR Code and DSK is found on the top of the Fan Speed Controller. If required, the pin code is underlined on the label.

2

Classic Exclusion

Exclusion From A Z-Wave Network When removing an fan speed controller from a Z-Wave network, best practice is to use the exclusion command found in the Z-Wave controller. 1. To enter programming mode, hold the button for 7 seconds. The status light will turn amber, release and the status light will blink. 2. Follow Z-Wave controller directions to enter exclusion mode 3. Tap the the top of the paddle 1 time. The status light will quickly flash green. 4. The Z-Wave controller will remove the device from the network

1

Classic Inclusion

Classic Inclusion To A Z-Wave Network For older controllers Classic Inclusion is supported. Depending on the age of the controller the controller will need to be 3 to 35 feet from the device when including. 1. To enter programming mode, hold the button for 7 seconds. The status light will turn amber, release and the status light will blink. 2. Follow the Z-Wave controller instructions to enter inclusion mode. 3. Tap the top or the paddle of the paddle one time. The status light will quickly flash green. 4. The Z-Wave controller will confirm successful inclusion to the network.

5

Factory Reset Procedure

Factory Default When removing a fan speed controller from a network it is best practice to use the exclusion process. In situations where a device needs to be returned to factory default follow the following steps. A reset should only be used when a controller is inoperable or missing. 1. Hold the top of the paddle for 7 seconds, the status light will turn amber. Continue holding the top paddle for another 7 seconds (total of 14 seconds). The status light will quickly flash red/ amber. 2. Release the top of the paddle and the device will reset.