Product Recognition | |
|---|
Certification Number | ZC10-15040009 |
|---|
Name | Flood Multisensor |
|---|
Short Description | The flood multisensor PAT02 has flood, temperature and humidity, 3 sensors function in one, based on Z-Wave™ technology. |
|---|
Long Description | The flood multisensor PAT02 has flood, temperature and humidity, 3 sensors function in one, based on Z-Wave™ technology. Using Z-Wave™ plus technology, it supports security and Over-The-Air updating. |
|---|
Brand | Philio |
|---|
Product Identifier | PAT02-1A |
|---|
OEM Version | 01 |
|---|
Hardware Platform | SD3502 |
|---|
Z-Wave Version | 6.51.06 |
|---|
Library Type | SLAVE_ENHANCED_232 |
|---|
Device Type | Notification Sensor |
|---|
Role Type | ROLE_TYPE_SLAVE_SLEEPING_REPORTING |
|---|
Manufacturer ID | 0x013C |
|---|
Product Type ID | 0x0002 |
|---|
Product ID | 0x001F |
|---|
Frequency Plans | EU: 869.85MHz, 868.40MHz |
|---|
Categories | Sensors |
|---|
Countries / Regions | European Union |
|---|
Controlled Command Classes | Identifier | Name | Key | Version |
|---|
COMMAND_CLASS_BASIC | Basic | 0x20 | 1 |
|
|---|
Documents | Category | Description | File |
|---|
Manual_Primary_Lang | Product or Owner's Manual | |
|
|---|
Association Groups | Group Number | Maximum Nodes Supported | End Point ID | Description |
|---|
2 | 8 | 0 | The group 2 is for the light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes maximum. | 1 | 8 | 0 | The group 1 is for receiving the report message, like triggered event, temperature, humidity etc. |
|
|---|
Configuration Parameters | Parameter Number | Name | Description | Format | Size | Min Value | Max Value | Default Value | Parameter Values |
|---|
1 | Basic Set OFF Level | Setting the BASIC command value. When the flood trigger off(0x00), send the BASIC CC to the group 2. | 0 | 1 | 0 | 0 | 0 | From | To | Description |
|---|
0 | 255 | Setting the BASIC command value 0x00. |
| 2 | Basic Set ON Level | Setting the BASIC command value. When the flood trigger on(0xFF), send the BASIC CC to the group 2. | 0 | 1 | 0 | 0 | 255 | From | To | Description |
|---|
0 | 255 | Setting the BASIC command value 0xFF. |
| 6 | Mult-Sensor Function Switch | Multisensor function switch. Using bit to control. | 0 | 1 | 0 | 0 | 0 | From | To | Description |
|---|
64 | 64 | Disable the humidity report after event triggered. (1:Disable, 0:Enable) |
| 23 | Humidity Differential Report | The humidity differential to report. 0 means turn off this function. The unit is percentage. Enable this function the device will detect every 10 seconds. | 0 | 1 | 0 | 0 | 5 | From | To | Description |
|---|
0 | 60 | The humidity differential to report. |
|
|
|---|
Texts | ID | Description | Value |
|---|
1 | Inclusion | The device have auto inclusion function, if the device not add into Z-Wave network, after power up, it will into the auto inclusion (NWI) mode.
In this mode, let the Z-Wave™ Controller entered inclusion mode, the device will added.
The NWI mode will timeout in 30 seconds.
After that you can pressing the tamper key three times within 1.5 seconds to manual inclusion with Z-Wave controller.
After inclusion successful, the device will awake to receive the setting command from Z-Wave™ Controller about 20 seconds. | 2 | Exclusion | 1. Have Z-Wave™ Controller entered exclusion mode.
2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode.
Node ID has been excluded. | 4 | Device Wake-Up | When the device power on, the device will wake about 20 seconds. In this duration, the controller can communicate with the device. Normally the device is always sleeping to save the battery energy. | 6 | Additional Special Features | 1. Have Z-Wave™ Controller entered association mode.
2. Pressing tamper key three times within 1.5 seconds to enter the association mode.
Note: The device support 2 groups. The group 1 is for receiving the report message, like triggered event, temperature, humidity etc. The group 2 is for the light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes maximum. | 5 | Factory Reset | Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4th pressed, and the LED will light ON.
2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once.
3. IDs are excluded and all settings will reset to factory default. |
|
|---|
Supports NWI | Yes |
|---|
Supports Explorer Frames | Yes |
|---|
