Product Recognition | |
|---|
Certification Number | ZC10-15060011 |
|---|
Name | Flood sensor |
|---|
Short Description | The PAT02-1C is the flood sensor, based on Z-Wave technology. |
|---|
Long Description | The flood multisensor PAT02 has flood, based on Z-Wave™ technology. It is the Z-Wave™ plus product, it support the security, OTA... Those newest features of the Z-Wave™ technology.
Z-Wave™ is a wireless communication protocol designed for home automation, specifically to remotely control applications in residential and light commercial environments. The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. This product can be included and operated in any Z-Wave™ network with other Z-Wave™ certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. |
|---|
Brand | Philio |
|---|
Product Identifier | PAT02-1C |
|---|
OEM Version | 01 |
|---|
Hardware Platform | SD3502 |
|---|
Z-Wave Version | 6.51.06 |
|---|
Library Type | SLAVE_ENHANCED_232 |
|---|
Device Type | Notification Sensor |
|---|
Role Type | ROLE_TYPE_SLAVE_SLEEPING_REPORTING |
|---|
Manufacturer ID | 0x013C |
|---|
Product Type ID | 0x0002 |
|---|
Product ID | 0x0021 |
|---|
Frequency Plans | EU: 869.85MHz, 868.40MHz |
|---|
Categories | Sensors |
|---|
Countries / Regions | European Union |
|---|
Controlled Command Classes | Identifier | Name | Key | Version |
|---|
COMMAND_CLASS_BASIC | Basic | 0x20 | 1 |
|
|---|
Documents | Category | Description | File |
|---|
Manual_Primary_Lang | Product or Owner's Manual | |
|
|---|
Association Groups | Group Number | Maximum Nodes Supported | End Point ID | Description |
|---|
1 | 8 | 0 | The group 1 is for receiving the report message, like triggered event,
temperature, humidity etc.And each group support 8 nodes. | 2 | 8 | 0 | The group 2 is for the light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes. |
|
|---|
Configuration Parameters | Parameter Number | Name | Description | Format | Size | Min Value | Max Value | Default Value | Parameter Values |
|---|
1 | Basic Set OFF Level | Setting the BASIC command value. When the flood trigger off(0x00), send the BASIC CC to the group 2. | 0 | 1 | 0 | 0 | 0 | From | To | Description |
|---|
0 | 255 | Setting the BASIC command value 0x00. |
| 2 | Basic Set ON Level | Setting the BASIC command value. When the flood trigger on(0xFF), send the BASIC CC to the group 2. | 0 | 1 | 0 | 0 | 255 | From | To | Description |
|---|
0 | 255 | Setting the BASIC command value 0xFF. |
|
|
|---|
Texts | ID | Description | Value |
|---|
5 | Factory Reset | Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable.
1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4 th pressed, and the LED will light ON.
2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second.
Otherwise, the LED will flash once.
3. IDs are excluded and all settings will reset to factory default. | 4 | Device Wake-Up | When the device power on, the device will wake about 20 seconds. In
this duration, the controller can communicate with the device. Normally
the device is always sleeping to save the battery energy. | 2 | Exclusion | 1. Have Z-Wave™ Controller entered exclusion mode.
2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode. Node ID has been excluded. | 1 | Inclusion | 1. Have Z-Wave™ Controller entered inclusion mode.
2. Pressing the tamper key three times within 1.5 seconds to enter the inclusion mode.
3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds. | 6 | Additional Special Features | 1. Have Z-Wave™ Controller entered association mode.
2. Pressing tamper key three times within 1.5 seconds to enter the association mode.
Note: PAT02-1A and PAT02-1C are support 2 groups, and PAT02-1B only support 1 group. The group 1 is for receiving the report message, like triggered event, temperature, humidity etc. The group 2 is for the light control, the device will send the “Basic Set” command to this group. And each group support 8 nodes maximum. |
|
|---|
Supports NWI | Yes |
|---|
Supports Explorer Frames | Yes |
|---|
