COMMAND_CLASS_BASIC

Basic

0x20

1

Manual_Primary_Lang

Product or Owner's Manual

Battery Quantity

Battery Type

Firmware Updatable

IP (Ingress Protection) Rated

Sensors

1

5

0

The MultiSensor supports 1 association group. Group 1 is assigned to the Lifeline association group and can add max 5 association nodes. When the PIR motion sensor is triggered, the MultiSensor will send Basic Set (0xFF) to the associated nodes. If no PIR motion is triggered after the PIR interval time (configurable), the MultiSensor will send Basic Set (0x00) to the associated nodes. The automatically reports of temperature, humidity, luminance and ultraviolet (configurable) also can be sent to the associated nodes.

255

Reset to factory defaults.

Reset to factory defaults.

0

4

0

0

0

2

Enable/Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.

Enable/Disable waking up for 10 minutes when re-power on (battery mode) the MultiSensor.

0

1

0

0

0

3

Set the PIR time.

The default PIR time is 4 minutes. The Multisensor will send BASIC SET CC (0x00) to the associated nodes if no motion is triggered again in 4 minutes.

0

2

0

0

240

4

Set the sensitivity of the motion sensor.

This parameter changes the sensitivity level of the motion detector.

0

1

0

0

5

5

Which command would be sent when the motion sensor triggered.

To set which command would be sent when the motion sensor triggered.

0

1

0

0

1

9

Report the current power mode and the product state for battery power mode

Report the current power mode and the product state for battery power mode. Note: this parameter cannot be used as Set usage.

0

2

0

0

0

42

Threshold change in humidity to induce an automatic report

Threshold change in humidity to induce an automatic report. Note: 1. The unit is %. 2. The default value is 10, which means that if the current humidity gap is more than 10%, it will send out a humidity report.

0

1

0

0

10

43

Threshold change in luminance to induce an automatic report.

Threshold change in luminance to induce an automatic report.

0

2

0

0

100

44

Threshold change in battery level to induce an automatic report.

Threshold change in battery level to induce an automatic report. Note: 1. The unit is %. 2. The default value is 10, which means that if the current battery level gap is more than 10%, it will send out a battery report.

0

1

0

0

10

45

Threshold change in ultraviolet to induce an automatic report.

Threshold change in ultraviolet to induce an automatic report.

0

1

0

0

2

56

Set the lower limit value of ultraviolet sensor.

Set the lower limit value of ultraviolet sensor. When the measurement is less than this upper limit, which will trigger to sent out a sensor report.

0

1

0

0

4

46

Enable/disable to send the alarm report of low temperature

Enable/disable to send the alarm report of low temperature(<-15℃). Note: If it is enabled, the MultiSensor will send a report of Multi Level Temperature CC to controller when the current temperature is less than -15℃).

0

1

0

0

0

50

Set the lower limit value of temperature sensor.

Set the lower limit value of temperature sensor. When the measurement is less than this lower limit, which will trigger to sent out a sensor report. High byte is the lower limit value.

0

4

0

0

320

51

Set the upper limit value of humidity sensor.

Set the upper limit value of humidity sensor. when the measurement is more than this upper limit, which will trigger to sent out a sensor report.

0

1

0

0

60

52

Set the lower limit value of humidity sensor.

Set the lower limit value of humidity sensor. When the measurement is less than this lower limit, which will trigger to sent out a sensor report.

0

1

0

0

50

53

Set the upper limit value of Lighting sensor

Set the upper limit value of Lighting sensor. When the measurement is more than this upper limit, which will trigger to sent out a sensor report.

0

1

0

0

1000

54

Set the lower limit value of Lighting sensor.

Set the lower limit value of Lighting sensor. When the measurement is less than this lower limit, which will trigger to sent out a sensor report.

0

1

0

0

100

55

Set the upper limit value of ultraviolet sensor.

Set the upper limit value of ultraviolet sensor. When the measurement is more than this upper limit, which will trigger to sent out a sensor report.

0

1

0

0

8

48

Enable/disable to send a report when the measurement is more than the upper limit value or less than the lower limit value.

Enable/disable to send a report when the measurement is more than the upper limit value or less than the lower limit value.

0

1

0

0

0

49

Set the upper limit value of temperature sensor.

Set the upper limit value of temperature sensor. When the measurement is more than this upper limit, which will trigger to sent out a sensor report.

0

4

0

0

824

58

Set the recover limit value of humidity sensor.

Set the recover limit value of humidity sensor. Note: 1. When the current measurement <= (Upper limit – Recover limit), the upper limit report is enabled and then it would send out a sensor report when the next measurement is more than the upper limit. After that the upper limit report would be disabled again until the measurement = (Lower limit + Recover limit), the lower limit report is enabled and then it would send out a sensor report when the next measurement is less than the lower limit. After that the lower limit report would be disabled again until the measurement >= (Lower limit + Recover limit).

0

1

0

0

5

59

Set the recover limit value of Lighting sensor.

Set the recover limit value of Lighting sensor. Note: 1. When the current measurement <= (Upper limit – Recover limit), the upper limit report is enabled and then it would send out a sensor report when the next measurement is more than the upper limit. After that the upper limit report would be disabled again until the measurement = (Lower limit + Recover limit), the lower limit report is enabled and then it would send out a sensor report when the next measurement is less than the lower limit. After that the lower limit report would be disabled again until the measurement >= (Lower limit + Recover limit). 3. Unit = 10×Recover limit (Lux)

0

1

0

0

100

60

Set the recover limit value of Ultraviolet sensor.

Set the recover limit value of Ultraviolet sensor. Note: 1. When the current measurement <= (Upper limit – Recover limit), the upper limit report is enabled and then it would send out a sensor report when the next measurement is more than the upper limit. After that the upper limit report would be disabled again until the measurement = (Lower limit + Recover limit), the lower limit report is enabled and then it would send out a sensor report when the next measurement is less than the lower limit. After that the lower limit report would be disabled again until the measurement >= (Lower limit + Recover limit).

0

1

0

0

2

64

Set the default unit of the automatic temperature report in parameter 101-103.

Set the default unit of the automatic temperature report in parameter 101-103.

0

1

0

0

2

81

Enable/disable the LED blinking when the PIR is triggered.

Enable/disable the LED blinking when the PIR is triggered.

0

1

0

0

0

100

Set the parameter 101-103 to default values.

Set the parameter 101-103 to default values.

0

1

0

0

0

101

To set which report would be sent in Report group 1

To set which report would be sent in Report group 1. Note: You can also set all sensor reports to be sent out at the same time. E.g. If you want the batter report and temperature report to be sent out at the same time, you just need to set the configuration value to 33 (1+32).

0

4

0

0

241

103

To set which report would be sent in Report group 3

To set which report would be sent in Report group 3. Note: You can also set all sensor reports to be sent out at the same time. E.g. If you want the batter report and temperature report to be sent out at the same time, you just need to set the configuration value to 33 (1+32).

0

4

0

0

0

111

To set the interval time of sending reports in Report group 1

To set the interval time of sending reports in Report group 1

0

4

0

0

3600

112

To set the interval time of sending reports in Report group 2

To set the interval time of sending reports in Report group 2

0

4

0

0

3600

113

To set the interval time of sending reports in Report group 3

To set the interval time of sending reports in Report group 3

0

4

0

0

3600

201

Temperature sensor calibration

Temperature sensor calibration. Note: 1. High byte is the calibration value. Low byte is the unit (0x01=Celsius, 0x02=Fahrenheit) 2. The calibration value (high byte) contains one decimal point. E.g. if the value is set to 20 (0x1401), the calibration value is 2.0 ℃ (EU/AU version) or if the value is set to 20 (0x1402), the calibration value is 2.0 ℉(US version) 3. The calibration value (high byte) = standard value - measure value. E.g. If measure value =25.3℃ and the standard value = 23.2℃, so the calibration value= 23.2℃ - 25.3℃= -2.1℃ (0xEB). If the measure value =30.1℃ and the standard value = 33.2℃, so the calibration value= 33.2℃ - 30.1℃=3.1℃ (0x1F).

0

2

0

0

0

202

Humidity sensor calibration

Humidity sensor calibration. The calibration value = standard value - measure value. E.g. If measure value =80RH and the standard value = 75RH, so the calibration value= 75RH – 80RH= -5RH (0xFB). If the measure value =85RH and the standard value = 90RH, so the calibration value= 90RH – 85RH=5RH (0x05).

0

1

0

0

0

203

Luminance sensor calibration

Luminance sensor calibration. The calibration value = standard value - measure value. E.g. If measure value =800Lux and the standard value = 750Lux, so the calibration value= 750 – 800= -50 (0xFFCE). If the measure value =850Lux and the standard value = 900Lux, so the calibration value= 900 – 850=50 (0x0032)

0

2

0

0

0

204

Ultraviolet sensor calibration

Ultraviolet sensor calibration. The calibration value = standard value - measure value. E.g. If measure value =9 and the standard value = 8, so the calibration value= 8 – 9= -1 (0xFE). If the measure value =7 and the standard value = 9, so the calibration value= 9 – 7=2 (0x02).

0

1

0

0

0

252

Enable/disable all configuration parameters to be locked

Enable/disable all configuration parameters to be locked.

0

1

0

0

0

1

Inclusion

Turn the primary controller of Z-Wave network into inclusion mode, short press the product’s Z-Wave button that you can find in the back of the product.

2

Exclusion

Turn the primary controller of Z-Wave network into exclusion mode, short press the product’s Z-Wave button that you can find in back of the product.

5

Factory Reset

Press and hold the Z-Wave button that you can find in back of the product for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable.

4

Device Wake-Up

Pressing the Z-Wave button once will trigger sending the Wake up notification command. If press and hold the Z-Wave button for 3 seconds, the MultiSensor will wake up for 10 minutes.

6

Additional Special Features

Support ""Over the Air Firmware Updating"" and “Z-Wave Security”.

Air temperature

0x02

Illuminance

Humidity

Ultraviolet