Product Recognition
Certification Number	ZC10-16010010
Name	Building 36 Temperature Sensor
Short Description	Battery powered Z-Wave temperature sensor.
Long Description	Battery powered indoor Z-Wave temperature sensor. Sense temperature in any room in the home.
Brand	Building 36
Product Identifier	B36-S10
OEM Version	01
Hardware Platform	ZM5202
Z-Wave Version	6.51.06
Library Type	SLAVE_ENHANCED_232
Device Type	Multilevel Sensor
Role Type	ROLE_TYPE_SLAVE_SLEEPING_REPORTING
Manufacturer ID	0x0190
Product Type ID	0x0003
Product ID	0x0001
Frequency Plans	US: 916.00MHz, 908.40MHz
Categories	Sensors
Countries / Regions	United States of America
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual Temperature Sensor_Product Manual_UPDATED3.pdf
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 5 0 Z-Wave Plus Lifeline. 2 5 0 Sensor Multilevel Temperature Report.
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 4 Configuration Bitmask Configuration bitmask for various device configuration settings. Bit 0 - reserved. Bit 1 - If set to 1, sensor will send unsolicited temperature reports. Bits 2 to 15 - reserved 0 2 0 0 2 From To Description 0 0 If zero, sensor will not send unsolicted temperature reports 2 2 If Bit 1 is set, sensor will send unsolicited temperature reports when the temperature changes. 5 Battery Reporting Interval The number wakeup intervals between autonomous battery reports. 0 2 0 0 8 From To Description 0 0 0 255 Number of wake up intervals between autonomous battery reports. The wake up interval is set in the Wake Up Command Class. 6 Temperature Checking Interval The number of seconds between temperature readings. 0 2 0 0 60 From To Description 0 0 10 255 The number of seconds between temperature readings 8 Temperature Calibration Offset Adjust reported temperature by +/- 10 degrees Fahrenheit for calibration. 0 2 0 0 0 From To Description -100 100 Tenths of a degree Fahrenheit. A value of 10 would be 1.0F. 0 0 9 Mandatory Temperature Reporting Interval Temperature will be reported regardless of differential from threshold. 0 2 0 0 7200 From To Description 60 64800 The number of seconds between temperature reports. 0 0 1 Wake Up Period Number of seconds the sensor will stay in the Wake up state following a button press. The sensor will go to sleep if it receives a wake up no more information frame. 0 2 0 0 600 From To Description 0 0 10 32768 Seconds to stay awake following button press 2 Low Battery Level Low Battery Report threshold. 0 2 0 0 1755 From To Description 1000 2500 Battery level 0 0 7 Temperature Reporting Interval The number wakeup intervals between autonomous temperature reports. These interval reports should be sent regardless of the setting of the temperature reporting threshold. 0 2 0 0 0 From To Description 0 255 The number of wake up intervals between autonomous temperature reports. If this value is zero, autonomous temperature reporting based on wake up interval is disabled. 0 0 3 Temperature Reporting Threshold The minimum temperature difference required to send a new ambient temperature report. 0 2 0 0 10 From To Description 0 0 0 100 Tenths of a degree Fahrenheit. A value of 10 would be 1.0F.
Texts	ID Description Value 5 Factory Reset NOTE: Only reset the sensor to factory default when the primary controller is missing or inoperable. Press and hold the button for 15 seconds. Release the button after 15 seconds and the LED will blink rapidly when the sensor has been reset to factory default. 4 Device Wake-Up The temperature sensor will send wake up notifications when the button is pressed and the temperature sensor is already included in a Z-Wave network. It also sends wake up notifications based at time intervals specified in the wake up set command. 1 Inclusion Put the Z-Wave controller into add mode (refer to controller documentation for more information). Press the button on the sensor to add to the Z-Wave network. The LED on the sensor will go solid white when the sensor has been successfully added. 2 Exclusion Put the Z-Wave controller into remove mode (refer to the controller documentation for more information). Press the button on the sensor to remove from the Z-Wave network. The LED on the sensor will blink white when the sensor has been successfully removed.
Supports NWI	Yes
Supports Explorer Frames	Yes