Product Recognition
Certification Number	ZC10-16020013
Name	Wall Plug
Short Description	Smart power plug, control the on/off of electric appliance
Long Description	This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. In the front casing, there is button that is used to carry out include, exclude or reset factory default settings on PCB Board. When power is first supplied, the LED will flash on and off with yellow alternately every 1 second intervals within 5 seconds if the detector has not been added a Z-Wave network, otherwise the LED will flash on and off 5 times with cyan alternately every 300 millisecond. Please get familiar with the terms below before starting the operations. This Plug has function that remembers the relay states, the plug will turn on after power up next time if the plug is turn on before the power cut-off.
Brand	Coolcam
Product Identifier	NAS-WR01Z
OEM Version	41
Hardware Platform	ZM5202
Z-Wave Version	6.51.06
Library Type	SLAVE_ENHANCED_232
Device Type	On/Off Power Switch
Role Type	ROLE_TYPE_SLAVE_ALWAYS_ON
Manufacturer ID	0x0258
Product Type ID	0x0003
Product ID	0x0087
Frequency Plans	US: 916.00MHz, 908.40MHz
Categories	All Lighting Devices, On/Off Switches/Devices
Countries / Regions	United States of America
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual Smart-Plug User Guide.pdf
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 3 0 Associations Through an association this Plug may control another Z-Wave network device, e.g. a alarm device, wall plug, lighting etc. The Wall Plug provides three association groups, and every group can be support to associated 5 devices max. GROUP 1 is lifeline service that assigned to plug status – ON/OFF. It enables the Plug to send reports and readings to Z-Wave Controller or Z-Wave Gateway. This Group Support: NOTIFICATION_REPORT_V4 COMMAND_CLASS_METER_V4 COMMAND_CLASS_SWITCH_BINARY DEVICE_RESET_LOCALLY_NOTIFICATION GROUP 2 allows for sending control commands to associated devices such as Siren, relay module, lighting, etc. If current load is over the max current defined in parameter #3, the Plug will send a BASIC_SET (0xFF) to associated devices. When current load is normal, plug will send a BASIC_SET (0x00) to associated devices. This Group Support: BASIC_SET GROUP 3 allows for Send Notification to associated devices in this group. This Group Support: NOTIFICATION_REPORT_V4
Texts	ID Description Value 1 Inclusion Add the Device (Smart Plug) to Z-Wave Network 1.Make sure the sensor is powered. 2.Set Z-Wave controller or Z-Wave gateway into inclusion mode (Refer to the controller or gateway operating manual) 3.Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off with green alternately five times within 2 seconds. 2 Exclusion Delete the Device (Smart Plug) from Z-Wave Network 1.Make sure the sensor is powered. 2.Set Z-Wave controller or Z-Wave gateway into exclusion mode (Refer to the controller or gateway operating manual) 3.Press the button three times within 1.5 second, the device will enter exclusion mode. And the LED will flash on and off with yellow alternately five times within 2 seconds. 5 Factory Reset Restore the Device (Smart Plug) to Factory Default Settings Reset procedure will delete all information on the Z-Wave network and Z-Wave controller or Z-Wave Gateway, and restore the sensor to factory default settings. 1.Make sure the sensor is powered. 2.Press and hold the button more than 10 seconds until the LED blink with red color. 3.Release the button. Notice: Please use this procedure only in the event that the network primary controller is missing or otherwise inoperable. 4 Device Wake-Up this power plug is connected to power, not battery powered 6 Additional Special Features SPECIFICATIONS Power Supply: AC110 ~ 230V(±10%), 50/60Hz Rate Load Current: 13A, 110-230V, 50/60Hz – Continuous Load 16A, 110-230V, 50/60Hz – Momentary Load Power Consumption: 0.13W EU Standards Compliance: Radio Protocol: Z-Wave Radio Frequency: EU – 868.4MHz US – 908.4MHz Valid Range: Up to 60m outdoors Up to 30m indoors (Depending on terrain and building structure) Operational Temperature: 0 – 40 ℃
Supports NWI	Yes
Supports Explorer Frames	Yes