COMMAND_CLASS_SENSOR_BINARY

Sensor Binary

0x30

1

COMMAND_CLASS_SWITCH_MULTILEVEL

Switch Multilevel

0x26

1

COMMAND_CLASS_ASSOCIATION_GROUP_INFORMATION

Association Group Information V1

0x59

0

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel Association V3

0x8E

3

COMMAND_CLASS_BATTERY

Battery

0x80

1

COMMAND_CLASS_SENSOR_MULTILEVEL

Sensor Multilevel

0x31

1

COMMAND_CLASS_SWITCH_BINARY

Switch Binary

0x25

1

COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_CONFIGURATION

Configuration

0x70

1

COMMAND_CLASS_CRC_16_ENCAP

CRC16 Encapsulation

0x56

1

COMMAND_CLASS_SECURITY

Security S0

0x98

1

COMMAND_CLASS_NOTIFICATION_V3

Notification V3

0x71

3

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_WAKE_UP_V2

Wake Up V2

0x84

2

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_MULTI_CHANNEL_V4

Multi-Channel V4

0x60

4

COMMAND_CLASS_MANUFACTURER_SPECIFIC

Manufacturer Specific

0x72

1

Manual_Primary_Lang

Product or Owner's Manual

1

1

0

Z-Wave Plus Lifeline; Device reset local

23

Controller Inclusion

Note: Z-Wave requires a Z-Wave module connected to an EA controller. See the Z-Wave Module Installation Guide for more help. 1. Launch Composer. In the Project Tree, select the Project Name (top line of the project tree) object for the project properties to appear. 2 Click on the Z-Wave Configuration tab. 3 Check the box under Z-Wave Enabled for the controller you want to be your Z-Wave controller. 4 In System Design, enter the name of driver for the device that you wish to enter into your Z-Wave network in the Search tab. 5 Double-click on the device to add it into the project. You can also right-click on the device and select Add to Project to add the device driver. 6 If you have more than a couple of Z-Wave devices, it is recommended that you rename this driver to help with troubleshooting multiple devices. Right-click on the driver and select Rename. Enter a descriptive name and press Enter. 7 In Connections in the Network tab, select Z-Wave Network. 8 Double-click on the Z-Wave device driver to open the identify window or highlight the device and click on the Identify button. 9 Identify (add) the Z-Wave device according to the manufacturer’s instructions, usually by pressing a Z-Wave button on the device. See the documentation for the Z-Wave device for more information. 10 If the device is added, configured, and identified successfully, the address will show in the address field and the timer instructions will change to say “Identification Successful”. Note: Only one Z-Wave controller can be configured in a Control4 project. The configuration should show a status of “Secure” when it is configured properly. If the Status field is empty, make sure the Z-Wave module is connected and installed properly, and that the EA controller is online and identified in the project.

24

Controller Exclusion

1. Launch Composer. In Connections in the Z-Wave Network, click Remove in the Available Devices window. 2 Remove the Z-Wave device from the network according to the manufacturer’s instructions, usually by pressing a Z-Wave button on the device. See the documentation for the Z-Wave device for more information. 3 If the device was removed successfully, the timer will stop and the window will say the devices was removed from the network. 4 If the device is not removed from the network before the timer ends, close the window and click the Remove button to try again.

5

Factory Reset

Use this procedure only in the event that the network primary controller is missing or otherwise inoperable. 1. Launch Composer. Click on the Z-Wave Configuration tab in the project properties window. 2. Click on ""Reset Defaults"". This clears the Home ID on the Z-Wave controller and abandons any nodes on the existing network. Any Z-Wave devices previously joined to the network must be removed before they can join the new network.

3

Learn Mode (adding another controller)

1. Launch Composer. In the Project Tree, select the Project Name (top line of the project tree) object for the project properties to appear. 2 Click on the Z-Wave Configuration tab. 3 Press the Learn button. This option joins the selected controller to another open Z-Wave mesh. This action will change the Home ID of the controller, and any devices on the previous Home ID will no longer be available. If the controller is joined to a mesh that contains a Node ID controller (SUC/SIS), the controller will be an Inclusion controller with the Home ID of the mesh it joined.