Product Recognition
Certification Number	ZC10-16065126
Name	LED Bulb
Short Description	Aeotec LED Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave.
Long Description	Aeotec LED Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave. It’s a bulb has a Smart RGB LED, which can be used to add colour to your home. The bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm White and Cold White. You can configure its colour according to your favour. The LED Bulb is also a security Z-Wave device and supports the Over The Air (OTA) feature for the product’s firmware upgrade.
Brand	Aeotec
Product Identifier	ZW098-C55
OEM Version	HW: 98 FW: 1.05
Hardware Platform	ZM5101
Z-Wave Version	6.51.06
Library Type	SLAVE_ENHANCED_232
Device Type	Light Dimmer Switch
Role Type	ROLE_TYPE_SLAVE_ALWAYS_ON
Manufacturer ID	0x0086
Product Type ID	0x0003
Product ID	0x0062
User Icon	0x0600
Installer Icon	0x0600
Frequency Plans	EU: 869.85MHz, 868.40MHz
Categories	All Lighting Devices, Dimming Lighting Devices
Countries / Regions	European Union
Controlled Command Classes	Identifier Name Key Version COMMAND_CLASS_BASIC Basic 0x20 1 COMMAND_CLASS_HAIL Hail 0x82 1
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual LED Bulb manual.pdf
Features	Feature Values Switch Type Value Toggle Z-Wave Scene Type Value Scene
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 5 0 The association group 1 is the Z-Wave Lifeline group. The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1. 2 5 0 In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2 when the Bulb receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller.
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 80 To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed. To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed. 0 1 0 0 1 From To Description 0 0 Nothing 1 1 Hail CC 2 2 Basic CC report. 112 Set the Dimmer mode. Set the Dimmer mode. 0 1 0 0 0 From To Description 0 0 Parabolic curve mode 1 1 Index curve mode 2 2 (Parabolic + Index)/2 mode 3 3 Linear mode 252 Enable/disable Lock Configuration Enable/disable to lock Configuration parameters. 0 1 0 0 0 From To Description 0 0 Disable 1 1 Enable 255 Reset the Bulb Reset the Bulb to factory default. 0 4 0 0 0 From To Description 0 0 Reset all configuration parameters to factory default settings 1431655765 1431655765 Reset the bulb to factory default.
Texts	ID Description Value 6 Additional Special Features Support ""Over the Air Firmware Updating"" and “Z-Wave Security”. 1 Inclusion Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on. 2 Exclusion Turn the primary controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times. 5 Factory Reset Turn the controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times. After the LED Bulb is excluded from network, it will be reset to factory default state. Use this procedure only in the event that your primary network controller is missing or inoperable.
Supports NWI	Yes
Supports Explorer Frames	Yes