Product Recognition
Certification Number	ZC10-16085168
Name	Strips-MaZw
Short Description	Open/Close Magnet-sensor for doors & windows
Long Description	Strips by Sensative is an ultra-thin magnetic sensor designed to monitor windows and doors for your safety. It´s so thin that it can be mounted invisibly in the tiny gap between the frame and the door or window. It is as easy to mount as a sticker using Strips's adhesive tape. Strips is Z-Wave plus compliant and can be used with any existing Z-Wave smarthome systems.
Brand	Sensative
Product Identifier	11 01 011
OEM Version	HW: 2 FW: 0.06:00.07
Hardware Platform	ZM5101
Z-Wave Version	6.51.06
Library Type	SLAVE_ROUTING
Device Type	Notification Sensor
Role Type	ROLE_TYPE_SLAVE_SLEEPING_REPORTING
Manufacturer ID	0x019A
Product Type ID	0x0003
Product ID	0x0003
User Icon	0C 07
Installer Icon	0C 07
Frequency Plans	EU: 869.85MHz, 868.40MHz
Categories	Sensors
Countries / Regions	European Union
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual v0.7_ENGLISH_PDF_Sensative_Strips_languages_170x63.pdf
Features	Feature Values Battery Quantity Value 1 Battery Type Value Built in 3.0V LiMnO2 Color Value White Outdoor Use Sensors Value Open/Closed (Binary)
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 1 0 Z-Wave Plus Lifeline
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 1 Notification type User can use this configuration parameter to change the notification type compatible with their gatewaycontroller. 0 1 0 0 1 From To Description 2 2 Basic report 0 0 Binary Sensor report 1 1 Notification report 2 LED indication LED On during specific event detected (ex. door opened) else if the parameter value is 0, LED will be turned OFF for the specific event detected. 0 1 0 0 1 From To Description 1 1 On 0 0 Specific event indication (ex. door opened) Off
Texts	ID Description Value 6 Additional Special Features Failure message: 5 LED blinks 2 Exclusion 1. Set the controller in remove mode (See your controller’s manual). 2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the remove process was successful. 4 Device Wake-Up Wake up Strips manually for Z-Wave communication: 1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. 3. Repeat 3 times in total within 10 seconds. 1 Inclusion Strips is delivered in ""auto-add"" mode. Follow the process below to add Strips in a Z-Wave network. 1. Start the add mode on the Z-Wave controller. See the controller’s manual. 2. Remove both magnets from Strips. Strips blinks twice to confirm the command and successful addition. 3. A long LED blink indicates that the add process was successful 4. The Z-Wave controller application should now allow you to monitor your Strips sensor status. 5. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly. 6. If the Z-Wave system does not respond, it may be needed to change Strips’ notification type. Manual add: 1. Set the controller to add mode (See your controller’s manual). 2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. A long LED blink indicates that the add process was successful. 5 Factory Reset In order to reset Strips (only possible when the connection to the controller is lost): 1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. 3. On the 3rd repetition, leave the magnet at the rounded edge for 10s. 4. A long LED signal indicates success.
Supported Multilevel Sensors	Multilevel Sensor Type 0x02
Supports NWI	Yes
Supports Explorer Frames	Yes