Product Recognition
Certification Number	ZC10-16105297
Name	Siren Alarm
Short Description	This product can be included and operated in any Z‐Wave network with other Z‐Wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Long Description	In the front casing, there is button that is used to carry out include, exclude or reset factory default settings on PCB Board. When power is first supplied, the LED will flash on and off alternately at one second intervals within 5 seconds if the detector has not been added a Z‐Wave network. Please get familiar with the terms below before starting the operations. This product can be included and operated in any Z‐Wave network with other Z‐Wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Brand	Coolcam
Product Identifier	NAS-AB01Z
OEM Version	HW: 48 FW: 2.65
Hardware Platform	ZM5202
Z-Wave Version	6.51.08
Library Type	SLAVE_ROUTING
Device Type	Siren
Role Type	ROLE_TYPE_SLAVE_SLEEPING_LISTENING
Manufacturer ID	0x0258
Product Type ID	0x0003
Product ID	0x0088
User Icon	0x0F00
Installer Icon	0x0F00
Frequency Plans	US: 916.00MHz, 908.40MHz
Categories	Security Add-Ons
Countries / Regions	United States of America
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual Siren User Manual Common V3_5.pdf
Features	Feature Values Battery Type Value CR123A Color Value White Communications Connections Value RS-232 (Serial) Communications Protocol Value Z-Wave Serial API Firmware Updatable Value Updatable by Manufacturer Z-Wave Scene Type Value Scene Battery Quantity Value 2
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 5 0 GROUP 1 is lifeline service that assigned to Siren status. It enables the Siren to send reports and readings to Z‐Wave Controller or Z‐Wave Gateway whenever the sensor is triggered. This Group Support: SWITCH_BINARY_REPORT, NOTIFICATION_REPORT, BATTERY_REPORT, DEVICE_RESET_LOCALLY_NOTIFICATION 2 5 0 GROUP 2 allows for Send Binary Switch Report to associated devices in this group. This Group Support: SWITCH_BINARY_REPORT 3 5 0 GROUP 3 allows for Send Notification to associated devices in this group. This Group Support: NOTIFICATION_REPORT
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 3 Configuring Door Bell Music Duration Time This parameter defines the door bell music duration time when siren receives a door/window sensor notification report or an alarm command (BASIC_SET = 0x02) from controller. The door bell music will be played always if this parameter is set to ‘255’. The door bell music will not be played if this parameter is set to ‘0’. Other values are the door bell music playing duration time. Unit: Time. 0 1 0 0 1 From To Description 0 255 unsigned 1 Configure Alarm Music Volume This parameter defines the output volume when siren plays door bell music. Door Bell music volume is divided into 3 stages, Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High (Parameter is set to ‘3’). Default value is ‘3’. 0 1 0 0 3 From To Description 1 3 unsigned 4 Configure Door Bell Music Volume This parameter defines the output volume when siren plays alarm music. Door Bell music volume is divided into 3 stages, Low (Parameter is set to ‘1’), Middle (Parameter is set to ‘2’), High(Parameter is set to ‘3’). Default value is ‘1’. 0 1 0 0 1 From To Description 1 3 unsigned 5 Configure Alarm Music Index This parameter defines the alarm music index for siren play different music when alarm occurs. There are 10 different music for user selection. 0 1 0 0 10 From To Description 1 10 unsigned 6 Configure Door Bell Music Index This parameter defines the door bell music index for siren play different music when alarm occurs. There are 10 different music for user selection. 0 1 0 0 9 From To Description 1 10 unsigned 8 Configure Alarm Led Enable This parameter defines the default led enable status when siren is on for ALARM MUSIC MODE. If parameter is set to ‘0’, led will be disable. If parameter is set t0 ‘1’, led will be enable. When siren is on, the led will blink. 0 1 0 0 1 From To Description 0 1 unsigned 9 Configure Door Bell Led Enable This parameter defines the default led enable status when siren is on for DOOR BELL MUSIC MODE. If parameter is set to ‘0’, led will be disable. If parameter is set t0 ‘1’, led will be enable. When siren is on, the led will blink. 0 1 0 0 0 From To Description 0 1 unsigned 2 Configure Alarm Music Duration Time This Parameter defines the alarm music duration time when siren receive an alarm sensor notification report or an alarm command from controller. The duration time is divided into 5 stages: Siren is not on (Parameter is set to ‘0’), 30 second (Parameter is set to ‘1’), 1 minute (Parameter is set to ‘2’), 5 minute (Parameter is set to ‘3’) and Siren is always on until battery is dead (Parameter is set to ‘255’). Default value is ‘2’. 0 1 0 0 2 From To Description 0 3 unsigned 255 255 unsigned 7 Configure Default Siren On Mode This parameter defines the default music index, volume and the duration time forsiren on. This parameter can be selected between ALARM MUSIC and DOOR BELL MUSIC. The settings for ALARM MUSIC MODE defines by Param #1, #2 and #5. The settings for DOOR BELL MUSIC MODE defines by Param #3, #4 and #6. If parameter is set to ‘1’, siren will select ALARM MUSIC MODE to play music; If parameter is set to ‘2’, siren will select DOOR BELL MUSIC MODE to play music; 0 1 0 0 1 From To Description 1 2 unsigned
Texts	ID Description Value 2 Exclusion 1. Remove the siren cover. 2. Make sure the siren is powered. 3. Set Z‐Wave controller or Z‐Wave gateway into inclusion mode (Refer to the controller or gateway operating manual) 4. Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off alternately five times. Note: If siren has not been added to Z‐wave network, the siren will enter inclusion mode automatically when it is powered on. You should let the controller enter into inclusion first before power on the siren in order to run this function. 3 Learn Mode (adding another controller) 1. Remove the siren cover. 2. Make sure the siren is powered. 3. Set Z‐Wave controller or Z‐Wave gateway into exclusion mode (Refer to the controller or gateway operating manual) 4. Press the button three times within 1.5 second, the device will enter exclusion mode. 4 Device Wake-Up You can press the button once to wake up the device and send wakeup notification to controller. If press successfully, the LED will blink one time 1 Inclusion In the front casing, there is button that is used to carry out include, exclude or reset factory default settings on PCB Board. When power is first supplied, the LED will flash on and off alternately at one second intervals within 5 seconds if the detector has not been added a Z‐Wave network. Please get familiar with the terms below before starting the operations. This product can be included and operated in any Z‐Wave network with other Z‐Wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. 5 Factory Reset Reset procedure will delete all information on the Z‐Wave network and Z‐Wave controller or Z‐Wave Gateway, and restore the siren to factory default settings. 1. Remove the device cover. 2. Make sure the siren is powered. 3. Press and hold the button for 10 seconds, led will blink once. 4. Release the button. Note: to use the reset procedure only when the primary controller is missing or inoperable.
Supports NWI	Yes
Supports Explorer Frames	Yes
Is Flirs	Yes