COMMAND_CLASS_SENSOR_MULTILEVEL_V5

Sensor Multilevel V5

0x31

5

COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_BATTERY

Battery

0x80

1

COMMAND_CLASS_CONFIGURATION

Configuration

0x70

1

COMMAND_CLASS_SECURITY

Security S0

0x98

1

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_WAKE_UP_V2

Wake Up V2

0x84

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_NOTIFICATION_V5

Notification V5

0x71

5

COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Firmware Update Meta-Data V2

0x7A

2

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Manufacturer Specific V2

0x72

2

COMMAND_CLASS_BASIC

Basic

0x20

1

Manual_Primary_Lang

Product or Owner's Manual

Color

Firmware Updatable

Battery Type

Sensors

Supported Notification Types

Battery Quantity

2

5

0

1. Basic Set Multisensor will send Basic Set to associated nodes when the PIR is triggered.

1

5

0

1. Notification Report. Sensor will send Notification Report to the associated nodes when Multisensor is removed or/and PIR is triggered. 2. Sensor Multilevel Report. Multisensor will send Sensor Multilevel Report to the associated nodes at setting interval. 3. Battery Report. Multisensor will send Battery Report when the battery level is low and the battery report’s value is 0xFF. 4. Device Reset Locally Notification.

170

No.170 SET PARAMETER 171 – 174 TO DEFAULT SETTINGS

Set parameter 171,172,173,174 to default settings

0

1

0

0

0

171

BATTERY REPORT INTERVAL

The interval of sending battery report to association device (Group Lifeline). The reports are sent even if there are no changes in the battery level.

0

4

0

0

1800

172

TEMPERATURE REPORT INTERVAL

The interval of sending temperature report to association device (Group Lifeline). The reports are sent even if there are no changes in the temperature level.

0

4

0

0

1800

173

HUMIDITY REPORT INTERVAL

The interval of sending Humidity report to association device (Group Lifeline). The reports are sent even if there are no changes in the humidity level.

0

4

0

0

1800

174

LUMINANCE REPORT INTERVAL

The interval of sending luminance report to association device (Group Lifeline). The reports are sent even if there are no changes in the luminance level.

0

4

0

0

1800

181

BATTERY REPORT THRESHOLD

The parameter determines the change in battery level resulting in battery report being sent to the main controller.

0

1

0

0

10

183

HUMITIDY REPORT THRESHOLD

The parameter determines the change in humidity level resulting in humidity report being sent to the main controller.

0

1

0

0

5

184

LUMINANCE REPORT THRESHOLD

The parameter determines the change in luminance level resulting in luminance report being sent to the main controller.

0

2

0

0

200

5

Factory Reset

Press and hold the Z-button for 20 seconds, Multisensor will send “Device_Reset_Locally” to the main controller and exclude from the Z-Wave network when the Z-Button is released, this procedure will reset the Sensor to factory default. Please include a request to use the reset procedure only when the primary controller is missing or inoperable.

2

Exclusion

Remove for exclusion; 1. Insert two CR123A batteries. 2. Set the Z-Wave network main controller into removing mode (see Z-Wave controller operating manual). 3. Triple clicking the Z-button. 4. If the removing is successful, the LED will blink slowly for 5 seconds and then turn off, otherwise you need to repeat the process from step 2.

1

Inclusion

2. Add for inclusion (non-security): 1) Insert two CR123A batteries. 2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual). 3) Triple clicking the Z-button. 4) If the inclusion is successful, the LED will blink less than 5 seconds and then keep on for 3 seconds, otherwise the LED will blink 5 seconds and then turn off, in which you need to repeat the process from step 2. Add for inclusion (security): 1) Insert two CR123A batteries. 2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual). 3) Press and hold the Z-button for 3 seconds. 4) If the inclusion is successful, the LED will blink fast for less than 5 seconds and then keep on for 3 seconds, otherwise the LED will blink fast for 5 seconds and then turn off, in which you need to repeat the process from step 2.

Access Control

(Refer to parameters): State idle

0x02

Illuminance

Humidity