There are over 4377 interoperable
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 10 | 2 | Activate/deactivate functions ALL ON / ALL OFF | 255 (Default) |
ALL ON active, ALL OFF active | |
| 0 | ALL ON is not active, ALL OFF is not active | ||||
| 1 | ALL ON is not active ALL OFF active | ||||
| 2 | ALL ON active ALL OFF is not active | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 110 | 2 | Temperature sensor offset settings | 32536 (Default) |
offset is 0.0C | |
| 1 to 100 | value from 0.1 degrees Celsius to 10.0 degrees Celsius is added to actual measured temperature. | ||||
| 1001 to 1100 | value from -0.1 degrees Celsius to -10.0 degrees Celsius is subtracted to actual measured temperature. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 120 | 1 | Temperature sensor reporting | 5 (Default) |
= 0,5 degrees Celsius | |
| 1 to 127 (Default) |
= 0,1 degrees Celsius - 12,7 degrees Celsius, step is 0,1 degrees Celsius | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 250 | 1 | Unsecure / Secure Inclusion | 0 (Default) |
Unsecure Inclusion | |
| 1 | Secure Inclusion | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 40 | 1 | Power reporting in Watts on power change for Q1 or Q2 | 10 (Default) |
default value | |
| 0 | reporting disabled | ||||
| 1 to 100 (Default) |
= 1% - 100% Reporting enabled. Power report is send (push) only when actual power (in Watts) in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 42 | 2 | Power reporting in Watts by time interval for Q1 or Q2 | 0 (Default) |
reporting disabled | |
| 1 to 32767 | = 1 second - 32767 seconds. Reporting enabled, power report is send with | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 71 | 1 | Operating modes | 0 (Default) |
shutter mode | |
| 1 | venetian mode (up/down and slate rotation) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 72 | 2 | Slats tilting full turn time | 150 (Default) |
= 1,5 seconds | |
| 0 | tilting time disabled | ||||
| 1 to 32767 (Default) |
= 0,01seconds - 327,67 seconds | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 73 | 1 | Slats position | 0 | Slats return to previously set position only in case of Z-wave control (not valid for limit switch positions) | |
| 1 (Default) |
Slats return to previously set position in case of Z-wave control, push-button operation or when the lower limit switch is reached | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 74 | 2 | Motor moving up/down time | 0 (Default) |
moving time disabled (working with limit switches) | |
| 1 to 32767 | = 0,1seconds - 3276,7seconds. After that time motor is stopped (relay goes to off state) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 76 | 1 | Motor operation detection | 6 (Default) |
= 0,6W | |
| 5 to 100 (Default) |
= (0,5W - 10W), step is 0,1W. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 78 | 1 | Forced Shutter DC calibration | 0 (Default) |
default value | |
| 1 | start calibration process (when calibration process is finished, completing full cycle - up, down and up, set the parameter 78 (Forced Shutter calibration) value back to 0 | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 85 | 1 | Power consumption max delay time | 8 (Default) |
= 800ms | |
| 3 to 50 (Default) |
= 0,3seconds - 5seconds (100ms resolution) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 86 | 1 | Power consumption at limit switch delay time | 8 (Default) |
8 = 800ms | |
| 3 to 50 (Default) |
= 0,3seconds - 5seconds (100ms resolution) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 90 | 1 | Time delay for next motor movement | 5 (Default) |
= 500ms | |
| 1 to 30 (Default) |
= 0,1seconds - 3seconds (100ms resolution) | ||||