There are over 4377 interoperable
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 1 | 1 | Minimum brightness level | 1 to 98 (Default) |
percentage level of brightness | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 10 | 2 | Timer functionality (auto - off) | 0 (Default) |
Function disabled | |
| 1 to 32767 | time to turn off measured in seconds (1s-9.1h) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 11 | 2 | ALL ON/ALL OFF function | 0 | ALL ON not active, ALL OFF not active | |
| 1 | ALL ON not active, ALL OFF active | ||||
| 2 | ALL ON active, ALL OFF not active | ||||
| 255 (Default) |
ALL ON active, ALL OFF active | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 13 | 1 | Force auto-calibration | 0 (Default) |
readout | |
| 1 | force auto-calibration of the load without FIBARO Bypass 2 | ||||
| 2 | force auto-calibration of the load with FIBARO Bypass 2 | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 14 | 1 | Auto-calibration status | 0 (Default) |
calibration procedure not performed or Dimmer 2 operates on manual settings | |
| 1 | Dimmer 2 operates on auto-calibration settings | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 15 | 1 | Burnt out bulb detection | 0 | function disabled | |
| 1 to 99 (Default) |
percentage value of power variation, compared to standard power consumption, measured during the calibration procedure (to be interpreted as load error/burnt out bulb) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 16 | 2 | Time delay of a burnt out bulb (parameter 15) or overload (parameter 39) detection | 0 | detection of a burnt out bulb disabled | |
| 1 to 255 (Default) |
delay time in seconds | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 19 | 1 | Forced switch on brightness level | 0 (Default) |
function disabled | |
| 1 to 99 | percentage level of brightness | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 2 | 1 | Maximum brightness level | 2 to 99 (Default) |
percentage level of brightness | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 20 | 1 | Switch type | 0 (Default) |
momentary switch | |
| 1 | toggle switch | ||||
| 2 | roller blind switch - two switches operate the Dimmer 2 (S1 to brighten, S2 to dim) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 21 | 1 | The value sent to associated devices on single click | 0 (Default) |
0xFF value is sent, which will set associated devices to their last saved state | |
| 1 | current Dimmer 2 state is sent, which will synchronize brightness level of associated devices (other dimmers for example) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 22 | 1 | Assign bistable key status to the device status | 0 (Default) |
Device changes status on key status change. | |
| 1 | Device status is synchronized with key status. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 23 | 1 | Double click option | 0 | double click disabled; | |
| 1 (Default) |
double click enabled. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 24 | 1 | Command frames sent in 2-nd and 3-rd association groups (S1 associations) | 0 (Default) |
all actions send to association groups; | |
| 1 | do not send when switching on the Dimmer (single click); | ||||
| 2 | do not send when switching off the Dimmer (single click); | ||||
| 4 | do not send when changing dimming level (holding and releasing); | ||||
| 8 | do not send on double click; | ||||
| 16 | send 0xFF value on double click. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 25 | 1 | Command frames sent in 4-th and 5-th association groups (S2 associations) | 0 (Default) |
all actions send to association groups; | |
| 1 | do not send when switching on the Dimmer (single click); | ||||
| 2 | do not send when switching off the Dimmer (single click); | ||||
| 4 | do not send when changing dimming level (holding and releasing); | ||||
| 8 | do not send on double click; | ||||
| 16 | send 0xFF value on double click | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 26 | 1 | The function of 3-way switch | 0 (Default) |
3-way switch function for S2 disabled; | |
| 1 | 3-way switch function for S2 disabled; | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 27 | 1 | Associations in Z-Wave network security mode | 0 | all groups (II-V) sent as non-secure | |
| 1 to 2 | group sent as secure | ||||
| 2 to 3 | group sent as secure | ||||
| 4 | group sent as secure | ||||
| 8 to 5 | group sent as secure | ||||
| 15 (Default) |
groups (II-V) sent as secure | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 28 | 1 | Scene activation functionality | 0 (Default) |
functionality deactivated; | |
| 1 | functionality activated. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 29 | 1 | Switch functionality of S1 and S2 | 0 (Default) |
standard mode; | |
| 1 | operates as S2, S2 operates as S1. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 3 | 1 | Incandescence level of dimmable compact fluorescent lamps | 1 to 99 (Default) |
percentage level of brightness | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 30 | 1 | Load control mode | 0 | forced leading edge control; | |
| 1 | forced trailing edge control; | ||||
| 2 (Default) |
control mode selected automatically (based on auto-calibration). | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 31 | 1 | Load control mode recognized during auto-calibration | 0 (Default) |
leading edge; | |
| 1 | trailing edge. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 32 | 1 | On/Off mode | 0 | on/off mode disabled (dimming is possible); | |
| 1 | on/off mode enabled (dimming is not possible | ||||
| 2 (Default) |
mode selected automatically | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 33 | 1 | Dimmability of the load | 0 (Default) |
Load recognized as dimmable; | |
| 1 | Load recognized as non-dimmable | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 34 | 1 | Soft-Start functionality | 0 | no soft-start; | |
| 1 (Default) |
short soft-start (0.1s) | ||||
| 2 | long soft-start (0.5s) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 35 | 1 | Auto-calibration after power on | 0 | No auto-calibration of the load after power on | |
| 1 (Default) |
Auto-calibration performed after first power on | ||||
| 2 | Auto-calibration performed after each power on | ||||
| 3 | Auto-calibration performed after first power on or after each LOAD ERROR alarm (no load, load failure, burnt out bulb), if parameter 37 is set to 1 also after alarms: SURGE (Dimmer 2 output overvoltage) and OVERCURRENT (Dimmer 2 output overcurrent) | ||||
| 4 | Auto-calibration performed after each power on or after each LOAD ERROR alarm (no load, load failure, burnt out bulb), if parameter 37 is set to 1 also after alarms: SURGE (Dimmer 2 output overvoltage) and OVERCURRENT (Dimmer 2 output overcurrent) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 37 | 1 | Behaviour of the Dimmer after overload or surge. | 0 | device permanently disabled until re-enabling by command or external switch | |
| 1 (Default) |
three atempts to turn on the load | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 38 | 2 | Brightness level correction for flickering loads | 0 | automatic correction disabled | |
| 1 to 254 | duration of correction in seconds | ||||
| 255 (Default) |
automatic correction always enabled | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 39 | 2 | Power limit - OVERLOAD | 0 | functionality disabled | |
| 1 to 350 (Default) |
1W-350W | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 4 | 2 | Incandescence time of dimmable compact fluorescent lamps | 0 to 255 (Default) |
0s - 25.5s | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 40 | 1 | Response to General Purpose Alarm | 0 | No reaction | |
| 1 | Turn on the load | ||||
| 2 | Turn off the load | ||||
| 3 (Default) |
Load blinking | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 41 | 1 | Response to Water Flooding Alarm | 0 | No reaction | |
| 1 | Turn on the load | ||||
| 2 (Default) |
Turn off the load | ||||
| 3 | Load blinking | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 42 | 1 | Response to Smoke, CO or CO2 Alarm | 0 | No reaction | |
| 1 | Turn on the load; | ||||
| 2 | Turn off the load | ||||
| 3 (Default) |
Load blinking | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 43 | 1 | Response to Temperature Alarm | 0 | No reaction | |
| 1 (Default) |
Turn on the load | ||||
| 2 | Turn off the load | ||||
| 3 | Load blinking | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 44 | 2 | Time of alarm state | 1 to 132767 (Default) |
1-32767 seconds | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 45 | 1 | OVERLOAD alarm report | 0 | No reaction | |
| 1 (Default) |
Send and alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 46 | 1 | LOAD ERROR alarm report | 0 | No reaction | |
| 1 (Default) |
Send and alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 47 | 1 | OVERCURRENT alarm report | 0 | No reaction | |
| 1 (Default) |
Send and alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 48 | 1 | SURGE alarm report | 0 | No reaction | |
| 1 (Default) |
Send and alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 49 | 1 | OVERHEAT and VOLTAGE DROP alarm report | 0 | No reaction | |
| 1 (Default) |
Send and alarm frame | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 5 | 1 | Automatic control - dimming step size | 1 to 99 (Default) |
dimming step percentage value | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 50 | 1 | Active power reports | 0 | power reports disabled | |
| 1 to 100 (Default) |
(1-100%) - power report threshold | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 52 | 2 | Periodic active power and energy reports | 0 | periodic reports disabled | |
| 1 to 32767 (Default) |
(1-32767 seconds) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 53 | 2 | Energy reports | 0 | energy reports disabled | |
| 1 to 255 (Default) |
(0,01 - 2,55 kWh) - report triggering threshold | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 54 | 1 | Self-measurement | 0 (Default) |
Self-measurement inactive | |
| 1 | Self-measurement active | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 58 | 1 | Method of calculating the active power | 0 (Default) |
measurement based on the standard algorithm | |
| 1 | approximation based on the calibration data | ||||
| 2 | approximation based on the control angle | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 59 | 2 | Approximated power at the maximum brightness level | 0 to 500 (Default) |
(0-500W) - power consumed by the load at the maximum brightness level. | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 6 | 2 | Automatic control - time of a dimming step | 0 to 255 (Default) |
(0-2.55s, in 10ms steps) | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 7 | 1 | Manual control - dimming step size | 1 to 99 (Default) |
dimming step percentage value | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 8 | 2 | Manual control - time of a dimming step | 0 to 255 (Default) |
(0-2.55s, in 10ms steps) | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 9 | 1 | Saving the state of the device after a power failure | 0 | the Dimmer 2 does not save the state before a power failure, it returns to „off” position | |
| 1 (Default) |
the Dimmer 2 restores its state before power failure | ||||