Z-Wave Products

There are over 4059 interoperable Z-Wave products throughout the world, and over 94 million Z-Wave products have been sold since our beginnings in 2001. All of them work together regardless of brand, because they're all based on the common Z - Wavestandard.Browse our Product Finder to see what Z -Wave can do for you.

Z-Wave Configuration Capabilities

Model: Recessed Door Sensor 7 (ZW187-B)

Z-Wave Certification Number: ZC12-20010031


Parameter Number

Parameter Size

Parameter Name

Description

1 1 Binary Sensor Report Enable/Disable Binary Sensor Report. Allow for backward compatibility to report Binary if Notification Report cannot be use for status changes.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 1 No No No

Value

 

Description

0   Disable. Sensor Binary Report will NOT be issued via Lifeline when Magnet is away or near.
1   Enable. Sensor Binary Report will be issued via Lifeline when Magnet is away or near.

Parameter Number

Parameter Size

Parameter Name

Description

101 2 Timed battery report Set how often battery is reported in minutes.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

70 1 14400 No No No

Value

 

Description

1   Set how often battery is reported in minutes.

Parameter Number

Parameter Size

Parameter Name

Description

2 1 Sensor Reports Reverse Sensor Reports (both Sensor Binary Report and Notification Report.)

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 1 No No No

Value

 

Description

0   Open Status when Magnet is away, Close Status when magnet is near.
1   Close Status when Magnet is away, Open Status when magnet is near.

Parameter Number

Parameter Size

Parameter Name

Description

3 1 Association Group 2 Settings Configure the Basic Set value. Determine the Basic Set value to control other Z-Wave devices directly when Magnet is away or near.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

1 0 6 No No No

Value

 

Description

0   Disable completely.
1   Send Basic Set 0xFF when Magnet is away, and send Basic Set 0x00 when Magnet is near.
2   Send Basic Set 0x00 when Magnet is away, and send Basic Set 0xFF when Magnet is near.
3   Only send Basic Set 0xFF when Magnet is away.
4   Only send Basic Set 0x00 when Magnet is near.
5   Only send Basic Set 0x00 when Magnet is away.
6   Only send Basic Set 0xFF when Magnet is near.

Parameter Number

Parameter Size

Parameter Name

Description

4 2 Application Layer Retry Configure retry number and wait time. The device supports an application retry mechanism when the application of the device has detected a transmission error when Basic Set, Sensor Binary Report or Notification Report (Access Control) message is sent out but fails to result in an ACK or a Supervision Report.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 1535 No No Yes

Value

 

Description

0   The Byte 1 is used to configure the number of retries. The valid value is 0-5. 0 means disable retry. The Byte 2 is used to confiqure the wait time between retries. The valid value is 0-255. Unit is 100ms.

Parameter Number

Parameter Size

Parameter Name

Description

5 1 Supervision Report Wait Time Configure Supervision Report Wait Time

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

15 1 50 No No Yes

Value

 

Description

1   Unit is 100ms. Note: Issuing Basic Set, Sensor Binary Report or Notification Report(Access Control) via association groups uses Supervision encapsulation only if sending commands with S2(or higher security) encapsulation. In other word, this parameter can be configured in any network, but works only in S2 (or higher security) network.

Parameter Number

Parameter Size

Parameter Name

Description

81 1 Led Indicator Control LED Indicator. Determine whether the LED flash or not when sending Basic Set, Sensor Binary Report, Notification Report (Access Control) or Wake Up Notification.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

3 0 3 No No No

Value

 

Description

0   Completely disable LED.
1   LED quickly flashes only when sending Basic Set, Sensor Binary Report or Notification Report (Access Control).
2   LED activates only when sending Wake Up Notification.
3   LED quickly flashes when sending Basic Set, Sensor Binary Report or Notification Report (Access Control), and activates when sending Wake Up Notification.

Parameter Number

Parameter Size

Parameter Name

Description

90 1 Low battery threshold Configure the low battery threshold. Induce battery report when battery level is less than or equal to threshold. Forward low battery report.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

30 10 50 No No No

Value

 

Description

10   10%-50%.