Z-Wave Products

There are over 4065 interoperable Z-Wave products throughout the world, and over 94 million Z-Wave products have been sold since our beginnings in 2001. All of them work together regardless of brand, because they're all based on the common Z - Wavestandard.Browse our Product Finder to see what Z -Wave can do for you.

Z-Wave Configuration Capabilities

Model: Water Sensor 7 Pro (ZWA019-A)

Z-Wave Certification Number: ZC12-20080098


Parameter Number

Parameter Size

Parameter Name

Description

10 2 Time Delay of "Off" command frame Off command is sent after a delay defined in this parameter.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 32400 No No No

Value

 

Description

0   seconds

Parameter Number

Parameter Size

Parameter Name

Description

11 2 Delay of Tamper Alarm Cancellation Time a tamper alarm is delayed.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 32400 No No No

Value

 

Description

0   seconds

Parameter Number

Parameter Size

Parameter Name

Description

12 1 Reporting Tamper Alarm Cancellation This parameter defines if the alarm cancellation event is reported.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

1 0 1 No No No

Bit (Value)

 

Description

0 (1)   Do not send Report
1 (2)   Send Report

Parameter Number

Parameter Size

Parameter Name

Description

16 1 Minimum Temperature change to report This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 18, may still be active.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

20 0 100 No No No

Value

 

Description

0   Disabled
1   1/10 degree

Parameter Number

Parameter Size

Parameter Name

Description

17 1 Minimum humidity change to report This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline. If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 18, may still be active.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

5 0 20 No No No

Value

 

Description

0   Disabled
1   %

Parameter Number

Parameter Size

Parameter Name

Description

18 2 Temperature and Humidity Periodic Reports This parameter defines the time interval to send an unsolicited report. If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 16 and 17, may still be active.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

43200 0 65535 No No No

Value

 

Description

0   Disabled
900   Seconds

Parameter Number

Parameter Size

Parameter Name

Description

255 4 Reset Parameter This parameter helps reset configuration parameters and the device to factory defaults 1 - 1431655764 (0x55555554) - Reset all Parameter settings to their default settings. 1431655765 - Completely factory reset sensor and send device reset locally notification.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 1431655765 No No No

Value

 

Description

1   Reset all Parameter settings to their default settings.
1431655765   Completely factory reset sensor and send device reset locally notification.

Parameter Number

Parameter Size

Parameter Name

Description

3 1 Visual LED Indications This parameter defines when LEDs will indicate events. Disabling all indications may extend battery life. Value 0 means - No Indications.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

7 0 7 No No No

Parameter Number

Parameter Size

Parameter Name

Description

4 1 Range Test after double click Allows to enable the activation of a Z-Wave range test with double clicking the tamper switch.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 1 No No No

Bit (Value)

 

Description

0 (1)   Disabled
1 (2)   Enabled

Parameter Number

Parameter Size

Parameter Name

Description

5 1 2nd Association Group Trigger This parameter defines the status of the magnet switch that causes sending a BASIC command to all devices of Association Group 2.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 2 No No No

Bit (Value)

 

Description

0 (1)   Switch after Water Leakage Start and Stop
1 (2)   Switch after Water Leakage Start and Stop
2 (4)   Switch after Water Leakage Start and Stop

Parameter Number

Parameter Size

Parameter Name

Description

6 1 Command Sent to Devices of Association Group 2 This parameter defines which commands is sent to 2nd Association Group

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

2 0 2 No No No

Bit (Value)

 

Description

0 (1)   On
1 (2)   Off
2 (4)   On and Off

Parameter Number

Parameter Size

Parameter Name

Description

7 1 BASIC command "On event" value This is the BASIC command value sent in case of "On" event.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

255 0 255 No No No

Value

 

Description

0   Value
255   Value

Parameter Number

Parameter Size

Parameter Name

Description

8 1 BASIC command "Off event" value This is the BASIC command value sent in case of "Off" event.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 255 No No No

Value

 

Description

0   Value
255   Value

Parameter Number

Parameter Size

Parameter Name

Description

9 2 Time Delay of "On" command frame On command is sent after a delay defined in this parameter.

Default Value

Minimum Value

Maximum Value

Read Only

Re-Inclusion

Advanced

0 0 32400 No No No

Value

 

Description

0   seconds