There are over 4393 interoperable
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 10 | 2 | Parameter no. 10 - Activate/deactivate functions ALL ON / ALL OFF | 255 (Default) |
ALL ON active, ALL OFF active | |
| 0 | ALL ON not active, ALL OFF not active | ||||
| 1 | ALL ON not active, ALL OFF active | ||||
| 2 | ALL ON active, ALL OFF not active | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 110 | 2 | Parameter no. 110 – Temperature Sensor Offset Settings | 32536 (Default) |
Offset is 0 °C | |
| 1 to 100 | Where 1 stands for 0.1°C and 100 stands for 10.0°C added to the actual measurement. | ||||
| 1001 to 1100 | Where 1001 stands for -0.1°C and 1100 stands for -10.0°C subtracted from the actual measurement. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 120 | 1 | Parameter no. 120 – Temperature Sensor Reporting Threshold | 0 | Reporting disabled | |
| 1 to 127 (Default) |
Where 1 stands for 0.1°C and 127 stands for 12.7°C. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 40 | 1 | Parameter no. 40 - Power reporting in Watts on power change for Q1 or Q2 | 0 | Power consumption reporting disabled | |
| 1 to 100 (Default) |
1% - 100% Power consumption reporting enabled. New value is reported only when the power consumption in real time changes by more than the percentage value set in this parameter, compared to the previous power consumption reading, starting at 1% (the lowest value possible). | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 42 | 2 | Parameter no. 42 – Power reporting in Watts by time interval for Q1 or Q2 | 0 (Default) |
Power consumption reporting disabled | |
| 1 to 32767 | 1 - 32767 seconds. Power consumption reporting enabled. Report is sent according to time interval (value) set here | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 71 | 1 | Parameter no. 71 – Operating modes | 0 (Default) |
Shutter mode | |
| 1 | Venetian mode (up/down and slate rotation) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 72 | 2 | Parameter no. 72 – Slats tilting full turn time | 0 | tilting time disabled | |
| 1 to 32767 (Default) |
0.01seconds – 327.67 seconds | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 73 | 1 | Parameter no. 73 – Slats position | 0 (Default) |
Slats return to the previously set position only after being activated via the Z-Wave gateway (hub) (not valid for limit switch positions) | |
| 1 | Slats return to the previously set position in case they were activated via the Z-Wave gateway (hub), push-button operation or when the lower limit switch is reached | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 74 | 2 | Parameter no. 74 – Motor moving up/down time | 0 (Default) |
moving time disabled (working with limit switches) | |
| 1 to 32767 | 0.1 seconds – 3276.7 seconds | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 76 | 1 | Parameter no. 76 - Motor operation detection | 0 | The value 0 means that reaching a limit switch will not be detected. | |
| 1 to 127 (Default) |
1 - 127W The value 0 means reaching a limit switch will not be detected. | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 78 | 1 | Parameter no. 78 - Forced Shutter calibration | 1 to 0 | - Start the calibration process. When the calibration process finishes (completing the full cycle - up, down and up again), set the value of the parameter 78 (Forced Shutter calibration) back to 0. | |
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 85 | 1 | Parameter no. 85 – Power consumption max delay time | 0 | time is set automatically | |
| 3 to 50 (Default) |
0.3seconds - 5seconds (100ms resolution) | ||||
Parameter Number |
Parameter Size |
Parameter Name |
Parameter Values |
||
| 90 | 1 | Parameter no. 90 – Time delay for next motor movement | 5 (Default) |
500ms | |
| 1 to 30 (Default) |
0.1seconds - 3seconds (100ms resolution) | ||||