Product Recognition
Certification Number	ZC10-14120002
Name	Building 36 Intelligent Thermostat
Short Description	The Building 36 Intelligent Thermostat allows you to take remote control of your energy use and automate temperature settings — offering a new level of comfort.
Long Description	The Building 36 Intelligent Thermostat gives you remote access and control of your thermostat. Enjoy effortless energy management, climate and ambiance control, custom automation and measurable results. Create custom smart schedules that automate your thermostat. Receive critical temperature alerts to know instantly when your thermostat reaches preset limits. Save energy by using location-based automation to have your thermostat adjust itself while you're out. This thermostat is part of an entire ecosystem of home automation products. It was built to provide a single integrated solution to give you more from your connected home.
Brand	Building 36
Product Identifier	B36-T10
OEM Version	1.0
Hardware Platform	ZM5202
Z-Wave Version	6.51.02
Library Type	SLAVE_ENHANCED_232
Device Type	Thermostat - HVAC
Role Type	ROLE_TYPE_SLAVE_ALWAYS_ON
Manufacturer ID	0x0190
Product Type ID	0x0001
Product ID	0x0001
Frequency Plans	US: 916.00MHz, 908.40MHz
Categories	Thermostats
Countries / Regions	United States of America
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual Product_Manual_11_25_14-spreads_B36.pdf
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 4 0 Z-Wave Plus Lifeline
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 25 Configurable Terminal Setting Control the function of the configurable terminal on the thermostat. 0 1 0 0 0 From To Description 2 2 H 1 1 W3 0 0 Disabled 3 3 DH 2 Heat Stages Number of heat stages if HVAC type is normal or number of auxiliary heat stages if HVAC type is heat pump. 0 1 0 0 2 From To Description 0 3 Number of Heat Stages 3 Number of Cool Stages Number of cool stages if normal or the number of heat pump stages if heat pump 0 1 0 0 2 From To Description 0 2 Cool Stages 4 Heat Fuel Type Denotes the heating fuel type. 0 1 0 0 1 From To Description 1 1 Electric (default) 0 0 Fossil Fuel 1 HVAC System Type The type of HVAC system, either normal or heat pump. 0 1 0 0 0 From To Description 0 0 Normal 1 1 Heat Pump 5 Calibration Temperature Used to adjust the ambient room temperature reading up or down to a more accurate value. This may be necessary if the thermostat is installed in a location with abnormal temperature conditions, such as in direct sunlight, near an open window, or on a wall adjacent to an unheated room. The value should be in 1.0 degree Fahrenheit increments. For example, to set the calibration to 2.0F, use value 20. 0 4 0 0 0 From To Description -100 100 Calibration Temperature Range (in deg. F) Precision is tenths of a degree. 8 Heat Staging Delay In a multistage system, the number of minutes the thermostat will wait before turning on the next heating stage. 0 1 0 0 5 From To Description 1 60 Heat Staging Delay (in min) 10 Balance Setpoint If the outside temperature falls below the balance setpoint, the thermostat will only use Auxiliary heating to heat and will not use the heat pump. The value should be in 1.0 degree Fahrenheit increments. For example, to set the balance setpoint to 45.0F, use value 450. 0 4 0 0 350 From To Description 0 950 Balance Setpont Range (in deg. F) Precision is tenths of a degree. 9 Cool Staging Delay In a multistage system, the number of minutes the thermostat will wait before turning on the next cooling stage. 0 1 0 0 5 From To Description 1 60 Cool Staging Delay (in min) 23 Temperature Display Units This parameter controls what thermostat units are displayed on the thermostat screen. It is independent of the temperature units used on the Z-Wave network. 0 1 0 0 1 From To Description 0 0 Celsius 1 1 Farenheit 11 Recovery Settings In a multistage system, the thermostat will use all stages to reach the target when in comfort mode. When in efficient mode, the thermostat will only use all stages to get within the differential temperature, at which time it will only use a single stage. 0 1 0 0 1 From To Description 0 0 Comfort 1 1 Efficient 17 Maximum Cool Setpoint Maximum cool target allowed. Attempts to set the cool target higher than this value will be ignored. The value should be in 1.0 degree Fahrenheit increments. For example, to set the maximum cool setpoint to 80.0F, use value 800. 0 4 0 0 950 From To Description 500 950 Max Cool Setpoint Range(in deg. F) Precision is tenths of a degree.
Texts	ID Description Value 1 Inclusion 1. Put the thermostat in OFF mode (No mode icons are lit). 2. Put the Z-Wave controller into add mode. Refer to the controller documentation for more information. 3. Press and hold the DOWN button on the thermostat to begin inclusion. Release the button when the RADIO icon lights up. 4. When the RADIO icon becomes solid, the thermostat has been added. 2 Exclusion 1. Put the thermostat in OFF mode (No mode icons are lit). 2. Press and hold the remove button on the Z-Wave controller. Refer to controller documentation for more information. 3. Press and hold the DOWN button on the thermostat to enter exclusion mode. Release the button when the RADIO icon lights up. 4. When the RADIO icon becomes solid the thermostat has now been successfully removed from the network. 5 Factory Reset Please use this procedure only when your primary controller is missing or otherwise inoperable. 1. Put the thermostat in OFF mode (No mode icons are lit). 2. Press and hold the UP button to show the firmware versions. 3. Once the firmware versions are shown, press and hold the DOWN button to enter RST mode. The thermostat should display ""RST"".
Supports NWI	Yes
Supports Explorer Frames	Yes