Product Recognition
Certification Number	ZC10-15120009
Name	COQON Qplug
Short Description	Wireless 16A Relay Switch with true-power Metering and Safety against Overtemperature and Overload.
Long Description	The wireless relay switch PSMZ0001 allows you to remotely control electrical appliances. It features a metering function to measure the power consumption and the accumulated energy usage of connected equipment. The built-in metering unit is of high quality: it calculates the true-power and also works for small loads from 1W upwards. This feature is important to have a correct measurement value also for electronic loads like led lamps. The PSMZ0001 has a built-in safety features that will switch-off the output in case of too high temperature or overload. Additionally the PSMZ0001 has a feature to switch the load on at zero voltage and switch the load off at zero current. This leads to a very high number of possible switching cycles also for difficult loads like led-lamps or motors, e.g. pumps.
Brand	Neusta Next GmbH
Product Identifier	PSMZ0001
OEM Version	HW: 255
Hardware Platform	ZM5101
Z-Wave Version	6.51.06
Library Type	SLAVE_ENHANCED_232
Device Type	On/Off Power Switch
Role Type	ROLE_TYPE_SLAVE_ALWAYS_ON
Manufacturer ID	0x0248
Product Type ID	0x0003
Product ID	0x0001
Frequency Plans	EU: 869.85MHz, 868.40MHz
Categories	Energy Meters, All Lighting Devices, On/Off Switches/Devices
Countries / Regions	European Union
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual PSMZ0001_V07_RC3.pdf
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 2 5 0 Group2: Sends COMMAND_CLASS_BASIC, BASIC_REPORT every time the load is connected. 1 5 0 Z-Wave Plus Lifeline / Group 1 (1) Sends COMMAND_CLASS_BASIC, BASIC_REPORT after every change of the output state (on/off). (2) Sends COMMAND_CLASS_METER_V2, METER_REPORT_V2 after every change of the measured energy or power value or after a timeout if the values stay unchanged. during If the energy or power value didn‘t change for a certain time.
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 31 Local Control On If „LocalControlOn“ is set (factory default state) the PMSZ001s output can be switched manually by the touch button. If „LocalControlOff“ is set, the PMSZ0001s output can only be switched through Z-Wave telegrams. In both modes the operational state of the mechanical switch is reported to association group 2. 0 1 0 0 0 From To Description 0 0 Local Control On 1 1 Local Control Off
Texts	ID Description Value 1 Inclusion When a PSMZ0001 that is not associated to a Z-Wave Network, is inserted into the mains outlet, it will flash once red followed by 2 green flashes followed by steady red flashing. The PSMZ0001 can now be added to (=inclusion) or removed from (=exclusion) a Z-Wave network: 1) start inclusion/exclusion on the primary controller 2) hold the touch button until the led shows green light 3) release the touch button The PSMZ0001 will confirm successful addition to the network by 5 green flashes. 2 Exclusion When a PSMZ0001 that is not associated to a Z-Wave network is inserted into the mains outlet, it will flash once red followed by 2 green flashes followed by steady red flashing. The PSMZ0001 can now be added to (=inclusion) or removed from (=exclusion) a Z-Wave network: 1) start inclusion/exclusion on the primary controller 2) hold the touch button until the led shows green light 3) release the touch button The PSMZ0001 will confirm successful removal/exclusion by steady red flashing. At the time of exclusion the device is factory reset. 5 Factory Reset Please use this procedure only if the primary controller is missing or inoperable: The device can be put into factory default state manually by the following procedure: 1) hold the touch-button until the led shows red light 2) release the touch-button and hold the touch-button again until the led starts to flash green The PSMZ0001 confirms the successful completion of the factory reset procedure by steady red flashing.
Supports NWI	Yes
Supports Explorer Frames	Yes