COMMAND_CLASS_BASIC

Basic

0x20

1

Manual_Primary_Lang

Product or Owner's Manual

1

1

0

Lifeline - report group

3

5

0

Trigger: Tamper - association group.

5

5

0

Trigger: Tamper ZW3 - association group for ZW3 backward compatibility.

4

5

0

Trigger: Motion ZW3 - association group for ZW3 backward compatibility.

2

5

0

Trigger: Motion - association group, value depends on the configuration.

4

PIR sensor’s “WINDOW TIME”

Period of time during which the number of moves set in parameter 3 must be detected in order for the PIR sensor to report motion. The higher the value, the more sensitive the PIR sensor. It’s not recommended to modify this parameter setting.

0

1

0

0

2

25

TAMPER CANCELLATION REPORTS

0

1

0

0

1

3

PIR sensor’s “PULSE COUNTER”

Sets the number of moves required for the PIR sensor to report motion. The higher the value, the less sensitive the PIR sensor. It’s not recommended to modify this parameter settings.

0

1

0

0

1

8

PIR SENSOR OPERATING MODE

The parameter determines the part of day in which the PIR sensor will be active. This parameter influences only the motion reports and associations. Tamper, light intensity and temperature measurements will be still active, regardless of this parameter settings.

0

1

0

0

0

9

NIGHT / DAY

The parameter defines the difference between night and day, in terms of light intensity, used in parameter 8.

0

2

0

0

200

24

TAMPER OPERATING MODES

The parameter determines the behaviour of tamper alarm and how it reports. It is an advanced feature serving much more functions than just detection of tampering.

0

1

0

0

0

42

ILLUMINATION REPORTS INTERVAL

Time interval between consecutive illumination reports. The reports are sent even if there are no changes in the light intensity. CAUTION Frequent reports will shorten the battery life. Parameter value under 5 may result in blocking the temperature reports.

0

2

0

0

3600

60

TEMPERATURE REPORT THRESHOLD

The parameter determines the change in level of temperature resulting in temperature report being sent to the main controller.

0

2

0

0

10

62

INTERVAL OF TEMPERATURE MEASURING

The parameter determines how often the temperature will be measured. The shorter the time, the more frequently the temperature will be measured, but the battery life will shorten. CAUTION When parameter value is set to 0, the temperature measurements may be performed at the device wake-up.

0

2

0

0

900

64

TEMPERATURE REPORTS INTERVAL

The parameter determines how often the temperature reports will be sent to the main controller. CAUTION Frequent reports will shorten the battery life. Parameter value under 5 may result in blocking the illumination reports.

0

2

0

0

0

81

LED BRIGHTNESS

The parameter determines the brightness of LED when indicating motion.

0

1

0

0

50

82

AMBIENT ILLUMINATION LEVEL BELOW WHICH LED BRIGHTNESS IS SET TO 1%

The parameter is relevant only when the parameter 81 is set to 0. CAUTION The value of parameter 83 must be higher than the value of parameter 82.

0

2

0

0

100

66

TEMPERATURE OFFSET

The value to be added to the actual temperature, measured by the sensor (temperature compensation).

0

2

0

0

0

89

LED INDICATING TAMPER ALARM

Indicating mode resembles a police car (white, red and blue).

0

1

0

0

1

83

AMBIENT ILLUMINATION LEVEL ABOVE WHICH LED BRIGHTNESS IS SET TO 100%

The parameter is relevant only when the parameter 81 is set to 0. CAUTION The value of parameter 83 must be higher than the value of parameter 82.

0

2

0

0

1000

2

Exclusion

1) Make sure tampering the device will not result in undesirable effects. Dismounting the sensor can trigger an alarm. 2) Open the sensor’s casing by turning the cover counter-clockwise. Enclosure lock is marked with a dot. 3) Make sure the sensor's battery is unlocked. 4) Set the main controller into learning mode (see main controller’s operating manual). 5) Quickly, triple click the B-button, located inside Fibaro Motion Sensor’s casing. LED diode will glow blue confirming that the device has sent the Node Info Z-Wave command frame.

4

Device Wake-Up

The Motion Sensor will wake up at a defined time interval and will ALWAYS try to communicate with the main controller. There is a possibility to wake up the device manually by clicking the B-button.

1

Inclusion

The Fibaro Motion Sensor can be included into the Z-Wave network by using the B-button. 1) Open the sensor’s casing by turning the cover counter-clockwise. Enclosure lock is marked with a dot. 2) Unlock battery by removing “I'm ready” stripe. 3) Make sure the device is located within the direct range of the main controller. 4) Set the main controller into learning mode (see main controller’s operating manual). 5) Quickly, triple click the B-button - LED diode will glow blue to confirm setting into learning mode. 6) Fibaro Motion Sensor will be detected and included into the Z-Wave network. Wait for the main controller to configure the sensor. 7) If necessary, wake up the Motion Sensor by clicking the B-button. 8) Close the sensor’s casing and install the device in desired place.

5

Factory Reset

Please use this procedure in the event that the system’s primary controller is missing or is inoperable. To reset the device: 1) Make sure the battery works and it’s correctly placed. 2) Press and hold the B-button for 4-6 seconds until the LED glows yellow signaling the 2nd option of the menu mode. 3) Release the B-button. 4) Again, press the B-button briefly. Successful reset will be confirmed with the LED changing colour to red and fading. For more information please check the user's manual.