COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_SWITCH_MULTILEVEL_V3

Switch Multilevel V3

0x26

3

COMMAND_CLASS_NOTIFICATION_V5

Notification V5

0x71

5

Manual_Primary_Lang

Product or Owner's Manual

Switch Load Capacity Watts

Switch Load Capacity Volt-Ampere

5

5

0

“Dimmer (S2)” is assigned to switch connected to the S2 terminal (uses Switch Multilevel command class).

4

5

0

“On/Off (S2)” is assigned to switch connected to the S2 terminal (uses Basic command class).

3

5

0

“Dimmer (S1)” is assigned to switch connected to the S1 terminal (uses Switch Multilevel command class).

1

1

0

“Lifeline” reports the device status and allows for assigning single device only (main controller by default).

2

5

0

“On/Off (S1)” is assigned to switch connected to the S1 terminal (uses Basic command class).

11

First channel - reaction to switch for delay/auto ON/OFF modes

This parameter determines how the device in timed mode reacts to pushing the switch connected to the S1 terminal. 0 - cancel mode and set target state 1 - no reaction to switch - mode runs until it ends 2 - reset timer - start counting from the beginning

0

1

0

0

0

58

Periodic power reports

This parameter determines in what time interval the periodic power reports are sent to the main controller. 0 - periodic reports are disabled 1-32000 (1-32000s) - report interval

0

2

0

0

3600

59

Periodic energy reports

This parameter determines in what time interval the periodic energy reports are sent to the main controller. 0 - periodic reports are disabled 1-32000 (1-32000s) - report interval

0

2

0

0

3600

51

First channel - minimal time between power reports

This parameter determines minimum time that has to elapse before sending new power report to the main controller. 0 - reports are disabled 1-120 (1-120s) - report interval

0

1

0

0

10

44

Flashing alarm duration

This parameter allows to set duration of flashing alarm mode. 1-32000 (1-32000s, 1s step) - duration

0

2

0

0

600

53

First channel - energy reports

This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller. 0 - reports are disabled 1-32000 (1-32000Wh) - change in energy

0

2

0

0

100

42

Reaction to CO/CO2/Smoke Alarm

This parameter determines how the device will react to CO, CO2 or Smoke frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame

0

1

0

0

3

43

Reaction to Heat Alarm

This parameter determines how the device will react to Heat Alarm frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame

0

1

0

0

1

41

Reaction to Flood Alarm

This parameter determines how the device will react to Flood Alarm frame. 0 - alarm frame is ignored 1 - turn ON after receiving the alarm frame 2 - turn OFF after receiving the alarm frame 3 - flash after receiving the alarm frame

0

1

0

0

2

60

Measuring energy consumed by the device itself

This parameter determines whether energy metering should include the amount of energy consumed by the device itself. Results are being added to energy reports for first endpoint. 0 - function inactive 1 - function active

0

1

0

0

0

9

Restore state after power failure

This parameter determines if the device will return to state prior to the power failure after power is restored. 0 - the device does not save the state prior to the power failure and returns to „off” position 1 - the device restores its state prior to the power failure

0

1

0

0

1

10

First channel - operating mode

This parameter allows to choose operating for the 1st channel controlled by the S1 switch. 0 - standard operation 1 - delay ON function 2 - delay OFF function 3 - auto ON function 4 - auto OFF function 5 - flash function

0

1

0

0

0

31

S1 switch - Switch ON value sent to 2nd and 3rd association groups

This parameter defines value sent with Switch ON command to devices associated in 2nd and 3rd association group. 0-255 - sent value

0

2

0

0

255

1

Inclusion

1) Switch off the mains voltage (disable the fuse). 2) Place the Switch 2 within the direct range of your Z-Wave controller. 3) Connect the device in accordance with one of the diagrams attached in the manual. 4) After verifying correctness of the connection switch on the mains voltage. 5) Identify the S1 switch or the B-button (located on the device’s housing). 6) Set the main controller in (security/non-security) add mode (see the controller’s manual). 7) Quickly, three times press the S1 switch or the B-button. 8) Wait for the adding process to end. 9) Successful adding will be confirmed by the Z-Wave controller’s message.

2

Exclusion

1) Place the Switch 2 within the direct range of your Z-Wave controller. 2) Identify the S1 switch or the B-button (located on the device’s housing). 3) Set the main controller in remove mode (see the controller’s manual). 4) Quickly, three times press the S1 switch or the B-button. 5) Wait for the removing process to end. 6) Successful removing will be confirmed by the Z-Wave controller’s message

4

Device Wake-Up

The FIBARO Single Switch 2 is powered with mains voltage so it is always awake.

5

Factory Reset

Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. In order to reset the device: 1) Switch off the mains voltage (disable the fuse). 2) Remove the Switch 2 from the wall switch box. 3) Switch on the mains voltage. 4) Press and hold the B-button to enter the menu. 5) Wait for the visual LED indicator to glow yellow. 6) Quickly release and click the B-button again. 7) After few seconds the device will be restarted, which is signalled with the red LED indicator colour. Use reset procedure only if the primary controller is missing or inoperable.

6

Additional Special Features

Z-Wave Plus communication protocol Active power and energy metering functionality Z-Wave range tester LED diode