Product Recognition
Certification Number	ZC10-16105298
Name	Motion Sensor (PIR)
Short Description	This product can be included and operated in any Z‐Wave network with other Z‐Wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network.
Long Description	This product can be included and operated in any Z‐Wave network with other Z‐Wave certified devices from other manufacturers and/or other applications. All non‐battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. In the Back casing, there is a button that is used to carry out include, exclude, wake up device or reset factory default settings. When power is first supplied, the LED will flash on and off alternately at one second intervals within 5 seconds if the detector has not been added a Z‐Wave network. Please get familiar with the terms below before starting the operations.
Brand	Coolcam
Product Identifier	NAS-PD01ZE
OEM Version	HW: 66 FW: 3.80
Hardware Platform	ZM5202
Z-Wave Version	6.51.06
Library Type	SLAVE_ROUTING
Device Type	Notification Sensor
Role Type	ROLE_TYPE_SLAVE_SLEEPING_REPORTING
Manufacturer ID	0x0258
Product Type ID	0x0003
Product ID	0x1083
User Icon	0x0C07
Installer Icon	0x0C07
Frequency Plans	EU: 869.85MHz, 868.40MHz
Categories	Sensors
Countries / Regions	European Union
Controlled Command Classes	Identifier Name Key Version COMMAND_CLASS_BASIC Basic 0x20 1
Documents	Category Description File Manual_Primary_Lang Product or Owner's Manual Motion Detector User Guide EU V3.3.pdf
Features	Feature Values Firmware Updatable Value Updatable by Manufacturer Z-Wave Scene Type Value Scene Battery Quantity Value 1 Battery Type Value CR123A Color Value White Communications Connections Value RS-232 (Serial) Communications Protocol Value Z-Wave Serial API
Association Groups	Group Number Maximum Nodes Supported End Point ID Description 1 4 0 GROUP 1 is lifeline service that assigned to Sensor (Motion detector) status – Open/Close. It enables the sensor to send reports and readings to Z‐Wave Controller or Z‐Wave Gateway whenever the sensor is triggered. This Group Support: NOTIFICATION_REPORT_V4 SENSOR_BINARY_REPORT_V2 SENSOR_MULTILEVEL_REPORT_V7 BATTERY_REPORT DEVICE_RESET_LOCALLY_NOTIFICATION 2 4 0 GROUP 2 allows for sending control commands to associated devices such as relay module, lighting, etc. This association group is configured through the advanced parameters no. 2, 3, 5 and 8. This Group Support: BASIC_SET 3 4 0 GROUP 3 allows for Send Notification to associated devices in this group. This Group Support: NOTIFICATION_REPORT_V4 4 4 0 GROUP 4 allows for Send Sensor Binary Report to associated devices in this group. This Group Support: SENSOR_BINARY_REPORT_V2
Configuration Parameters	Parameter Number Name Description Format Size Min Value Max Value Default Value Parameter Values 3 Basic Set Level Basic Set Command will be sent where contains a value when PIR detector is triggered, the receiver will take it for consideration; for instance, if a lamp module is received the Basic Set Command of which value is decisive as to how bright of dim level of lamp module shall be. This Parameter is used to some associated devices. 0 1 0 0 255 From To Description 0 0 0, 1 ~ 99 or 255 0 – OFF, Alarm cancelling or turning a device off 1 ~ 99 or 255 – ON (Binary Switch Device) Dim Level (Multilevel Switch Device) 4 Enabled/Disabled PIR Function This parameter can be enabled or disabled the PIR detector detecting function. 0 1 0 0 255 From To Description 0 0 – Disable PIR Detector Function. unsigned 255 255 – Enable PIR Detector Function. unsigned 6 Re‐trigger Interval Setting. This Parameter can be used to adjust the interval of being re‐triggered after the PIR detector has been triggered. This Parameter value must be less than Parameter 2#. If user set this parameter to default by Configure CC, the parameter #2 will be set to default value. 0 1 0 0 8 From To Description 1 8 second .unsigned 5 Lux Level Set This parameter can be set a lux level value which determines when the light sensor is activated. If the ambient illumination level falls below this value and a person moves across or within the detected area , PIR detector will send a Z‐Wave ON command(i.e. BASIC_SET (value = parameter 3) to an associated device and activate it. 0 2 0 0 100 From To Description 0 1000 Lux .unsigned 9 Lux Level Report This parameter defines by how much Lux Level must change, in lux, to be reported to the main controller. 0 2 0 0 100 From To Description 0 255 Lux. unsigned 10 Led Blink Enable This parameter defines the Led on/off enable. If this parameter is set to ‘1’, the led blink will be enabled, the led will blink once when motion sensor detect a movement. Otherwise, the led will be turned off always. 0 1 0 0 1 From To Description 0 1 unsigned 7 Light Sensor Polling Interval This Parameter can be set the light sensor measure ambient illumination level interval time. NOTE: This Value Must Be less than Wakeup Interval Time. 0 2 0 0 180 From To Description 60 36000 second .unsigned 8 Lux Level Enable If this parameter is set to ‘1’, and when Lux level less than the value define by parameter #5, PIR detector will send a BASIC_SET command frame(i.e. BASIC_SET (value = parameter 3) to an associated device and activate it. If Lux Level greater than the value define by parameter #5, PIR detector will not send a BASIC_SET command frame. 0 1 0 0 0 From To Description 0 1 unsigned
Texts	ID Description Value 1 Inclusion 1.Remove the sensor cover. 2.Make sure the sensor is powered. 3.Set Z‐Wave controller or Z‐Wave gateway into inclusion mode (Refer to the controller or gateway operating manual) 4.Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off alternately five times. 2 Exclusion 1.Remove the device cover. 2.Make sure the sensor is powered. 3.Set Z‐Wave controller or Z‐Wave gateway into exclusion mode (Refer to the controller or gateway operating manual) 4.Press the button three times within 1.5 second, the device will enter exclusion mode. 3 Learn Mode (adding another controller) 1. Remove the sensor cover. 2. Make sure the sensor is powered. 3. Set Z‐Wave controller or Z‐Wave gateway into inclusion mode (Refer to the controller or gateway operating manual) 4. Press the button three times within 1.5 second, the device will enter inclusion mode. And the LED will flash on and off alternately five times. 5 Factory Reset Reset procedure will delete all information on the Z‐Wave network and Z‐Wave controller or Z‐Wave Gateway, and restore the sensor to factory default settings. 1.Remove the device cover. 2.Make sure the sensor is powered. 3.Press and hold the button for 10 seconds, Led will blink once. 4.Release the button. Note: to use the reset procedure only when the primary controller is missing or inoperable. 4 Device Wake-Up You can press the button once to wake up the device and send wakeup notification to controller. If press successfully, the LED will blink one time
Supports NWI	Yes
Supports Explorer Frames	Yes