Ness Z-Wave Single Button – Z-Wave Alliance Product Catalog

Back to Listing

Product Recognition

Certification Number

ZC14-22090132

Name

Ness Z-Wave Single Button

Short Description

Long Description

The Ness Z-Wave™ Single Button (ZWSB) is a simple Z-Wave™ scene controller that allows you to control devices through the Z-Wave™ network and run various scenes defined in your Z-Wave™ gateways. Three different scenes can be triggered by a click, holding down and releasing the button. It also provides switch ON/OFF and dimming functions through the association groups. The ZWSB is equipped with Z-Wave™ 700 series chip and Z-Wave library SDK V7.16.3. It is a battery-powered device that can be quickly and easily installed into the Z-Wave network at any location within range.

Brand

Ness

Product Identifier

ZA-116011

Product Line

Single Button

OEM Version

HW: 01 FW: 01.01

Hardware Platform

ZGM130S037HGN2 / ZGM130S037HGN1

Z-Wave Version

7.16.3

Library Type

END_NODE_ENHANCED_232

Device Type

Central Scene DT

Role Type

ROLE_TYPE_SLAVE_SLEEPING_REPORTING

Manufacturer ID

0x0189

Product Type ID

0x0204

Product ID

0x0601

User Icon

0x1600

Installer Icon

0x1600

Frequency Plans

ANZ: 919.80MHz, 921.40MHz

Categories

Gateway Controller

Countries / Regions

Australia, New Zealand

Supported Command Classes

S2 Classes

S2_AUTHENTICATED, S2_UNAUTHENTICATED

Documents

Features

Association Groups

Configuration Parameters

Parameter Number	Name	Description	Format	Size	Default Value
1	The command to 2nd association group	This parameter defines how the Basic Set commands send to the nodes listed in 2nd association group after a Key Pressed 1 time scene event has triggered. 0 - No Basic Set commands send; 1 - Basic Set ON/OFF alternately; 2 - Basic Set ON with delay off; 3 - Basic Set OFF.	1	1	0x01
2	The Basic Set OFF Delay	The period of time in seconds to send Basic Set OFF command to Association Group 2 after BASIC Set ON command has reported. This parameter take affected only the option 2 has been selected in Configuration Parameter 1. 10 - disable BASIC Set OFF report; Time in seconds to send BASIC Set OFF command.	1	2	0x000A
3	The Key Held Down Duration	This parameter defines the duration that the key need to be pressed and held down to trigger the Key Held Down Scene event. The value is in seconds.	1	1	0x02
4	The commands to 3rd association group	This parameter defines how the Start Level Change/the Stop Level Change commands send to the nodes listed in 3rd association group. 0 - No any Start Level Change and Stop Level Change commands send; 1 - Send the Start Level Change/the Stop Level Change commands when the Key Held Down/the Key Released scene event has triggered; 2 - Send Start Level Change command when the Key Held Down. It does not sent the Stop Level Change command when the Key Released.	1	1	0x01
5	The duration of multilevel start level change	This parameter defines the duration in Switch Multilevel Start Level Change command. The value is in second. 0 - Instantly transition from the current value to the new target value; 1 ~ 120 - The time transition should take from the current value to the new target value.	1	1	0x02
6	Low battery setting	Report battery low warning message when battery level reaches this value in percentage. Range: 10~50 (10%~50%); The battery level range: 100% - 3V; 0% - 1.8V.	1	1	0x0A
7	Battery Scheduled Report Interval	The battery level scheduled report interval time is based on every 30 minutes per kick. The value N related to the time in minutes is N x 30 minutes. Range: 0~120. Default: 12 (12x30 =360 minutes). Value = 0 - Disable Battery level scheduled report.	1	1	0x0C

Texts

ID	Description	Value
8	Where to find S2 DSK on product	Page 7. Ness Z-Wave Single Button (ZWSB) is a SmartStart-enabled device allowing it to be added into a Z-Wave network by scanning its Z-Wave QR Code with a controller providing SmartStart inclusion. No further action is required and the SmartStart product will be added automatically within 10 minutes of being switched on in the network vicinity.
1	Classic Inclusion	Adding the device into a Z‑Wave Network Inclusion To add the device to the Z-Wave network: 1) Power on the device and ensure it has been factory defaulted. 2) Set the primary controller into inclusion mode. 3) Click the Action Button once to enter inclusion mode. Red LED: fast flashing. Inclusion mode can be cancelled by clicking the Action Button again before the controller starts inclusion mode. Red LED stops flashing. 4) If your Z-Wave controller supports S2 Access encryption and DSK, enter the first 5 digits of the DSK located at bottom of the QR image. 5) If Inclusion is successful: Red LED stops fast flashing. Green LED turns on for 2 seconds.
2	Classic Exclusion	Removing The device from a Z‑Wave Network The Exclusion process is the same as Inclusion however your Z-Wave controller must be in Exclusion mode. You may need to refer to your Z-Wave gateway/controller’s instructions for removing devices. Exclusion To remove the device from the Z-Wave network: 1) The device is powered 2) Set the primary controller into Exclusion mode. 3) Click the Action Button once. 4) If Exclusion is successful: Red LED stops fast flashing. Green LED turns on for 2 seconds.
4	Wake-Up Procedure	2. Wake-up To manually wake up the ZWSB, press and hold the Action Button for 3 seconds until the Blue LED turns on, then release the button.
5	Factory Reset Procedure	3. Factory Default To reset Ness ZWSB to factory default settings, press and hold the Action Button for at least 20 seconds. Release the button when the Blue LED turns off (20 seconds). The Green LED will flash once to indicate successful reset. Releasing the Action Button while the Blue LED is on cancels the reset process.

Supports NWI

Yes

Supports Explorer Frames

Yes

Supports SmartStart

Yes

Radio Range Z-Wave (m)