Roller Shutter 3 – Z-Wave Alliance Product Catalog

Back to Listing

Product Recognition

Certification Number

ZC10-19046413

Name

Roller Shutter 3

Short Description

FIBARO Roller Shutter 3 is a device designed to control roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices.

Long Description

FIBARO Roller Shutter 3 is a device designed to control roller blinds, awnings, venetian blinds, gates and other single phase, AC powered devices. Roller Shutter 3 allows precise positioning of roller blinds or venetian blind lamellas. The device is equipped with power and energy monitoring. It allows to control connected devices either via the Z-Wave network or via a switch connected directly to it. Main features of FIBARO Roller Shutter 3: - Compatible with any Z-Wave or Z-Wave Plus Controller, - Supports Z-Wave network Security Modes: S0 with AES-128 encryption and S2 with PRNG-based encryption, - To be installed with roller blind motors with electronic or mechanical limit switches, - Advanced microprocessor control, - Active power and energy metering functionality, - Works with various types of switches – momentary, toggle and dedicated roller blind switches, - To be installed in wall switch boxes, - Works as a Z-Wave signal repeater.

Brand

FIBARO

Product Identifier

FGR-223

OEM Version

HW: 3 FW: 5.01:05.01

Hardware Platform

ZM5101

Z-Wave Version

6.81.01

Library Type

SLAVE_ENHANCED_232

Device Type

Window Covering - Endpoint Aware

Role Type

ROLE_TYPE_SLAVE_ALWAYS_ON

Manufacturer ID

0x010F

Product Type ID

0x0303

Product ID

0x1000

User Icon

0x1900

Installer Icon

0x1900

Frequency Plans

EU: 869.85MHz, 868.40MHz

Categories

Energy Meters, Motor Control, Window Covering

Countries / Regions

European Union

Supported Command Classes

Controlled Command Classes

S2 Classes

S2_AUTHENTICATED

Documents

Features

Association Groups

Configuration Parameters

Parameter Number

Name

Description

Format

Size

Min Value

Max Value

Default Value

Parameter Values

Outputs orientation

This parameter allows reversing the operation of Q1 and Q2 without changing the wiring (in case of invalid motor connection) to ensure proper operation.

From	To	Description
0	0	default (Q1 - 1st channel, Q2 - 2nd channel)
1	1	reversed (Q1 - 2nd channel, Q2 - 1st channel)

Alarm configuration - 2nd slot (Water)

This parameter determines to which alarm frames and how the device should react. The parameters consist of 4 bytes, three most significant bytes are set according to the official Z-Wave protocol specification.

From	To	Description
1	1	Notification Type
2	2	Notification Status
3	3	Event/State Parameters
4	4	action: 0- no action, 1-open blinds, 2-close blinds

Inputs orientation

This parameter allows reversing the operation of switches connected to S1 and S2 without changing the wiring.

From	To	Description
1	1	reversed (S1 - 2nd channel, S2 - 1st channel)
0	0	default (S1 - 1st channel, S2 - 2nd channel)

S2 switch - scenes sent

This parameter determines which actions result in sending scene IDs assigned to them. NOTE: Parameter 41 values may be combined, e.g. 1+2=3 means that scenes for single and double click are sent.

From	To	Description
2	2	Key pressed 2 times
4	4	Key pressed 3 times
1	1	Key pressed 1 time
8	8	Key hold down and key released

Measuring power consumed by the device itself

This parameter determines whether the power metering should include the amount of active power consumed by the device itself.

From	To	Description
1	1	function active
0	0	function inactive

Energy reports - on change

This parameter determines the minimum change in consumed energy that will result in sending new energy report to the main controller.

From	To	Description
0	0	reports are disabled
1	500	change in energy

150

Force calibration

By setting this parameter to 2 the device enters the calibration mode. The parameter relevant only if the device is set to work in positioning mode (parameter 151 set to 1, 2 or 4).

From	To	Description
0	0	device is not calibrated
1	1	device is calibrated
2	2	force device calibration

151

Operating mode

This parameter allows adjusting operation according to the connected device.

From	To	Description
1	1	roller blind (with positioning)
4	4	gate (with positioning)
3	3	gate (without positioning)
6	6	roller blind with built-in driver (impulse)
5	5	roller blind with built-in driver
2	2	Venetian blind (with positioning)

152

Venetian blind - time of full turn of the slats

For Venetian blinds (parameter 151 set to 2) the parameter determines time of full turn cycle of the slats. For gates (parameter 151 set to 3 or 4) the parameter determines time after which open gate will start closing automatically (if set to 0, gate will not close). The parameter is irrelevant for other modes.

150

From	To	Description
0	965535	time of turn

153

Set slats back to previous position

For Venetian blinds (parameter 151 set to 2) the parameter determines slats positioning in various situations. The parameter is irrelevant for other modes. NOTE: If parameter 20 is set to 1 (toggle switch), change value of parameter 153 to 0 for slats to work properly.

From	To	Description
0	0	slats return to previously set position only in case of the main controller operation.
1	1	slats return to previously set position in case of the main controller operation, momentary switch operation, or when the limit switch is reached.
2	2	slats return to previously set position in case of the main controller operation, momentary switch operation, when the limit switch is reached or after receiving the Switch Multilevel Stop control frame

155

Motor operation detection

Power threshold to be interpreted as reaching a limit switch.

From	To	Description
0	0	reaching a limit switch will not be detected
1	255	report interval

156

Time of up movement

This parameter determines the time needed for roller blinds to reach the top. For modes with positioning value is set automatically during calibration, otherwise it must be set manually.

6000

From	To	Description
1	65535	(0.01 - 655.35s, every 0.01s) - movement time

157

Time of down movement

This parameter determines time needed for roller blinds to reach the bottom. For modes with positioning value is set automatically during calibration, otherwise it must be set manually.

6000

From	To	Description
1	65535	(0.01 - 655.35s, every 0.01s) - movement time

154

Delay motor stop after reaching end switch

For blinds (parameter 151 set to 1, 2, 5 or 6) the parameter determines the time after which the motor will be stopped after end switch contacts are closed. For gates (parameter 151 set to 3 or 4) the parameter determines time after which the gate will start closing automatically if S2 contacts are opened (if set to 0, gate will not close).

From	To	Description
0	255	time

Texts

ID	Description	Value
2	Exclusion	To remove the device from the Z-Wave network: 1. Make sure the device is powered. 2. Identify the S1 switch. 3. Set the main controller in remove mode (see the controller’s manual). 4. Quickly, triple click the S1 switch. 5. Wait for the removing process to end. 6. Successful removing will be confirmed by the Z-Wave controller’s message.
4	Device Wake-Up	FIBARO Roller Shutter 3 is powered with mains voltage so it is always awake.
1	Inclusion	To add the device to the Z-Wave network manually: 1. Power the device. 2. Identify the S1 switch. 3. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual). 4. Quickly, triple click the S1 switch. 5. If you are adding in Security S2, scan the DSK QR code or input the underlined part of the DSK (label on the bottom of the box). 6. Wait for the adding process to end. 7. Successful adding will be confirmed by the Z-Wave controller’s message. To add the device to the Z-Wave network using Smart Start: 1. Set the main controller in Security S2 Authenticated add mode (see the controller’s manual) 2. Scan the DSK QR code or input the underlined part of the DSK 3. (label on the bottom of the box). 4. Power the device (turn on the mains voltage). 5. LED will start blinking yellow, wait for the adding process to end. 6. Successful adding will be confirmed by the Z-Wave controller’s message.
5	Factory Reset	Reset procedure allows to restore the device back to its factory settings, which means all information about the Z-Wave controller and user configuration will be deleted. 1. Switch off the mains voltage (disable the fuse). 2. Remove the device from the wall switch box. 3. Switch on the mains voltage. 4. Press and hold the B-button to enter the menu. 5. Wait for the LED indicator to glow yellow. 6. Quickly release and click the B-button again. 7. After few seconds the device will be restarted, which is signalled with the red LED indicator colour. Please use this procedure only when the network primary controller is missing or otherwise inoperable.""

Supported / Controlled Meter Types

Supported Notification Types

Supported Multilevel Sensors

Supports NWI

Yes

Supports Explorer Frames

Yes

Supports SmartStart

Yes

Radio Range Z-Wave (m)