Roller Shutter 4 – Z-Wave Alliance Product Catalog

Back to Listing

Product Recognition

Certification Number

ZC14-23120375

Name

Roller Shutter 4

Short Description

FIBARO ROLLER SHUTTER 4 is a device designed to control roller blinds, awnings, venetian blinds, curtains and pergolas.

Long Description

FIBARO ROLLER SHUTTER 4 allows precise positioning of roller blinds or venetian blind slats. The device is equipped with ene rgy monitoring. It allows to control connected devices either via the Z-WaveTM network or via a switch connected directly to it.

Brand

FIBAR GROUP S.A.

Product Identifier

FGR-224

Product Line

Roller Shuter

OEM Version

HW: 04 FW: 08.01

Hardware Platform

EFR32ZG23B

Z-Wave Version

7.18.8

Library Type

END_NODE_ENHANCED_232

Device Type

Window Covering DT

Role Type

ROLE_TYPE_END_NODE_ALWAYS_ON

Manufacturer ID

0x010F

Product Type ID

0x0304

Product ID

0x1000

User Icon

0x1900

Installer Icon

0x1900

Frequency Plans

EU: 869.85MHz, 868.40MHz

Categories

Window Covering

Countries / Regions

European Union

Supported Command Classes

S2 Classes

S2_AUTHENTICATED, S2_UNAUTHENTICATED

Documents

Association Groups

Configuration Parameters

Texts

ID	Description	Value
8	Where to find S2 DSK on product	Enter the full DSK string code to your controller. If your controller is capable of QR scanning, scan the QR code placed on the label on the bottom of the box.
1	Classic Inclusion	To add the device to the Z-Wave network manually: 1. Power the device. 2. Identify the PROG button or the S1/S2 switches. 3. Set the main controller in (Security/non-Security Mode) add mode (see the controller’s manual). 4. Quickly, click PROG button three times. Optionally, click S1 or S2 three times. 5. If you are adding in Security S2 Authenticated, input the PIN Code (label on the device, also underlined part of the DSK on t he label on the bottom of the box). 6. Wait for the LED indicator to blink yellow. 7. Successful adding will be confirmed by the Z-Wave controller’s message and the device’s LED indicator: • Green – successful (non-secure, S0, S2 non-authenticated), • Magenta – successful (Security S2 Authenticated), • Red – not successful.
2	Classic Exclusion	Removing (Exclusion) – Z-Wave device learning mode, allowing to remove the device from existing Z-Wave network. To remove the device from the Z-Wave network: 1. Make sure the device is powered. 2. Identify the PROG button or the S1/S2 switches. 3. Set the main controller in remove mode (see the controller’s manual). 4. Quickly, click PROG button three times. Optionally, click S1 or S2 three times within 10 minutes of powering up the device. 5. Wait for the removing process to end. 6. Successful removing will be confirmed by the Z-Wave controller’s message and the device’s LED indicator - Red. 7. Removing the device from the Z-Wave network doesn’t cause factory reset.
5	Factory Reset Procedure	Reset procedure allows to restore the device back to its factor y settings, which means all information about the Z-Wave controller and user configuration will be deleted. 1. Switch off the mains voltage (disable the fuse). 2. Remove the device from the wall switch box. 3. Switch on the mains voltage. 4. Press and hold the PROG button to enter the menu. 5. Wait for the LED indicator to glow yellow. 6. Quickly release and click the PROG button again. 7. During the factory reset, the LED indicator will blink yellow. 8. After few seconds the device will be restarted, which is signal led with the red LED indicator colour.

Supported / Controlled Meter Types

Supported Notification Types

Supports NWI

Yes

Supports Explorer Frames

Yes

Supports SmartStart

Yes

Radio Range Z-Wave (m)