Wave Pro 1PM – Z-Wave Alliance Product Catalog

Back to Listing

Product Recognition

Certification Number

ZC14-24040420

Name

Wave Pro 1PM

Short Description

Long Description

Wave Pro 1PM is a DIN rail mountable smart switch with power measurement capabilities. It controls on/off function for one electrical device (with load up to 16 A), e.g., bulb, ceiling fan, IR heater, electrical locks, garage doors, irrigation system, etc. and it is compatible with push-buttons and switches (default). If the SW (SW1) is configured as a switch, each toggle of the switch will change the output O (O1) state to the opposite state - on, off, on, etc. If the SW (SW1) is configured as a push-button in the Device settings, each press of the push-button will change the output O (O1) state to the opposite state - on, off, on, etc. Highlights & Features: - 1 output, 16 A - Power metering - DIN-rail mountable - Extremely low power consumption: < 0.3 W - Z-Wave frequency band: 868.4 MHz (CEPT countries) - Latest technology: Z-Wave 800 Series - Automatic set-up with SmartStart - Security 2 Authenticated for the highest level of security - Over-the-air firmware updates - Works with Z-Wave-certified gateways and over 4,000 Z-Wave devices

Brand

Shelly Qubino

Product Identifier

QPSW-0A1P16EU

Product Line

Wave

OEM Version

HW: 01 FW: 11.00:02.02

Hardware Platform

EFR32ZG23A

Z-Wave Version

7.19.1

Library Type

END_NODE_ENHANCED_232

Device Type

Binary Switch DT

Role Type

ROLE_TYPE_END_NODE_ALWAYS_ON

Manufacturer ID

0x0460

Product Type ID

0x0002

Product ID

0x008B

User Icon

0x0700

Installer Icon

0x0700

Frequency Plans

EU: 869.85MHz, 868.40MHz

Categories

On/Off Switches/Devices

Countries / Regions

Armenia, Bahrain, European Union, Cyprus, Moldova, Egypt, French Guiana, Georgia, Iraq, Jordan, Kazakhstan, Kuwait, Lebanon, Libya, Maldives, Mauritius, Nigeria, Oman, Philippines, Qatar, Saudi Arabia, South Africa, Turkmenistan, United Arab Emirates, ZU, Yemen

Supported Command Classes

S2 Classes

S2_AUTHENTICATED, S2_UNAUTHENTICATED

Documents

Features

Association Groups

Configuration Parameters

Texts

ID	Description	Value
8	Where to find S2 DSK on product	When adding the Device to a Z-Wave network with a gateway supporting Security 2 (S2), the PIN Code of the Z-Wave Device Specific Key (DSK) is required. You can find it on the label on the side of the Device and a copy is inserted in the packaging, which must not be lost. Do not remove the Z-Wave DSK label from the Device. As a backup measure, use the label in the packaging. The first five digits of the key are highlighted or underlined to help the user identify the PIN Code part of the DSK text. The DSK is additionally represented with a QR Code as shown on the image.
1	Classic Inclusion	6.1 Adding the Device to a Z-Wave® network (inclusion) Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave® network. Note! In case of Security 2 (S2) adding (inclusion), a dialog will appear asking you to enter the corresponding PIN Code (5 underlined digits) that are written on the Z-Wave® DSK label on the side of the Device and on the Z-Wave® DSK label inserted in the packaging. IMPORTANT: The PIN Code must not be lost. SmartStart adding (inclusion) SmartStart enabled products can be added into a Z-Wave® network by scanning the Z-Wave® QR Code present on the Device with a gateway providing SmartStart inclusion. No further action is required, and the SmartStart device will be added automatically within 10 minutes of being switched on in the network vicinity. 1.With the gateway application scan the QR code on the Device label and add the Security 2 (S2) Device Specific Key (DSK) to the provisioning list in the gateway. 2.Connect the Device to a power supply. 3.Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network. 4.Adding will be initiated automatically within a few seconds after connecting the Device to a power supply, and the Device will be added to a Z-Wave® network automatically. 5.The blue LED will be blinking in Mode 2 during the adding process. 6.The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network. Adding (inclusion) with the S button 1.Connect the Device to a power supply. 2.Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network. 3.Enable add/remove mode on the gateway. 4.To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue. 5.Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode. 6.The blue LED will be blinking in Mode 2 during the adding process. 7.The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network. Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode. Adding (inclusion) with a switch/push-button 1.Connect the Device to a power supply. 2.Check if the blue LED is blinking in Mode 1. If so, the Device is not added to a Z-Wave® network. 3.Enable add/remove mode on the gateway. 4.Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2, etc.) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times. 5.The blue LED will be blinking in Mode 2 during the adding process. 6.The green LED will be blinking in Mode 1 if the Device is successfully added to a Z-Wave® network. Learn mode - a state that allows the Device to receive network information from the gateway.
2	Classic Exclusion	6.2 Removing the Device from a Z-Wave® network (exclusion) Note! The Device will be removed from your Z-Wave® network, but any custom configuration parameters will not be erased. Note! All Device outputs (O, O1, O2, etc. - depending on the Device type) will turn the load 1s on/1s off /1s on/1s off if the Device is successfully added to/removed from a Z-Wave® network. Removing (exclusion) with the S button 1.Connect the Device to a power supply. 2.Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave® network. 3.Enable add/remove mode on the gateway. 4.To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue. 5.Quickly release and then press and hold (> 2s) the S button on the Device until the blue LED starts blinking in Mode 3. Releasing the S button will start the Learn mode. 6.The blue LED will be blinking in Mode 2 during the removing process. 7.The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave® network. Note! In Setting mode, the Device has a timeout of 10s before entering again into Normal mode. Removing (exclusion) with a switch/push-button 1.Connect the Device to a power supply. 2.Check if the green LED is blinking in Mode 1. If so, the Device is added to a Z-Wave® network. 3.Enable add/remove mode on the gateway. 4.Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 3 times within 3 seconds (this procedure puts the Device in Learn mode). The Device must receive on/off signal 3 times, which means pressing the momentary switch 3 times, or toggling the switch on and off 3 times. 5.The blue LED will be blinking in Mode 2 during the removing process. 6.The blue LED will be blinking in Mode 1 if the Device is successfully removed from a Z-Wave® network.
5	Factory Reset Procedure	6.3 Factory reset Factory reset general After Factory reset, all custom parameters and stored values (kWh, associations, routings, etc.) will return to their default state. HOME ID and NODE ID assigned to the Device will be deleted. Use this reset procedure only when the gateway is missing or otherwise inoperable. Factory reset with the S button Note! Factory reset with the S button is possible anytime. 1. To enter the Setting mode, quickly press and hold the S button on the Device until the LED turns solid blue. 2. Press the S button multiple times until the LED turns solid red. 3. Press and hold (> 2s) S button on the Device until the red LED starts blinking in Mode 3. Releasing the S button will start the factory reset. 4. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s. 5. The blue LED will be blinking in Mode 1 if the Factory reset is successful. Factory reset with a switch/push-button Note! Factory reset with a switch/push-button is only possible within the first minute after the Device is connected to a power supply. 1. Connect the Device to a power supply. 2. Toggle the switch/push-button connected to any of the SW terminals (SW, SW1, SW2,…) 5 times within 3 seconds. The Device must receive on/off signal 5 times, which means pressing the push-button 5 times, or toggling the switch on and off 5 times. 3. During factory reset, the LED will turn solid green for about 1s, then the blue and red LED will start blinking in Mode 3 for approx. 2s. 4. The blue LED will be blinking in Mode 1 if the Factory reset is successful. Remote factory reset with parameter with a gateway Factory reset can be done remotely with the settings in Parameter No. 120.

Supported / Controlled Meter Types

Supported Notification Types

Supports NWI

Yes

Supports Explorer Frames

Yes

Supports SmartStart

Yes

Radio Range Z-Wave (m)