COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3

Multi-Channel Association V3

0x8E

3

COMMAND_CLASS_SWITCH_BINARY

Switch Binary

0x25

1

COMMAND_CLASS_BASIC

Basic

0x20

1

COMMAND_CLASS_CRC_16_ENCAP

CRC16 Encapsulation

0x56

1

COMMAND_CLASS_TRANSPORT_SERVICE_V2

Transport Service V2

0x55

2

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_MULTI_CHANNEL_V4

Multi-Channel V4

0x60

4

COMMAND_CLASS_SECURITY_2

Security S2

0x9F

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC

Manufacturer Specific

0x72

1

COMMAND_CLASS_SUPERVISION

Supervision

0x6C

1

COMMAND_CLASS_METER_V2

Meter V2

0x32

2

Manual_Primary_Lang

Product or Owner's Manual

Color

Supported Meter Type

1

1

0

Z-Wave Plus Lifeline Device Reset Locally is sent on completion of device local reset operation. After calibration, a METER_REPORT_V2 is sent every 60 seconds, for the controlled outlet for a non-multi-channel association, or for BOTH the controlled and always-on outlet for a multi-channel association. Meter report contains electricity consumed in Watts : Rate Type 0x01 Import (consumed) Meter Type 0x01 Electric meter Precision 0x02 Number of decimal places in meter value Scale 0x02 Watts Size 0x04 4-byte report Meter Value Byte 1 (MSB) 0xXX MSB of 32-bit meter value Meter Value Byte 2 0xXX meter value data Meter Value Byte 3 0xXX meter value data Meter Value Byte 4 (LSB) 0xXX LSB of 32-bit meter value Delta Time 1 0x00 No previous meter data included Delta Time 2 0x00 No previous meter data included Meter reports for the controlled outlet are sent from the ROOT for NODE associations. Meter reports for both the controlled outlet AND the always-on outlet are sent from the endpoint 1, and endpoint 2 when the association destination is set as a multi-channel association.

1

Inclusion

NOTE: Before beginning the network add procedure, ensure there are no devices plugged into either receptacle outlet. After the device has ben successfully added to the network, DO NOT plug anything into either receptacle outlet for at least 2 minutes to allow the module time to synchronize with the outlet metering hardware, or the accuracy of your meter readings may be adversely affected. 1. Follow network ADD steps for your Z-Wave controller/hub to prepare the network to accept a device addition. 2. Lightly press the push button on the Swidget Z-Wave Insert and hold for 10-15 seconds until the LED illuminates solid blue, then release the button. The LED will flash blue to indicate ADD mode is enabled. No manual or external Z-Wave operations are possible during this activity. 3. The Swidget Z-Wave Insert will remain in ADD mode for up to 60 seconds. If the device is successfully added to the Z-Wave network, the LED will be solid blue for 5 seconds then return to the normal operational state; LED will be solid green if switch is ON (default), LED will not be illuminated if switch is OFF. If the device fails to be successfully added to the network after 60 seconds, the red LED will begin to flash. If necessary, consult your Z-Wave controller/hub manual and re-try. 4. Please see section 4.4 on how to perform a local device reset if multiple remove attempts fail.

2

Exclusion

1. Follow network REMOVE steps for your Z-Wave controller/hub. 2. Lightly press the push button on the Swidget Z-Wave Insert and hold for approximately 10 seconds until the LED illuminates solid blue, then release the button. The LED will flash blue to indicate REMOVE mode is enabled. 3. The Swidget Z-Wave Insert will remain in REMOVE mode for up to 60 seconds. If the device is successfully removed from the Z-Wave network, the LED will be solid blue for 5 seconds then return to the normal operational state. If the device fails to be successfully removed from the network after 60 seconds, the red LED will begin to flash. If necessary, consult your Z-Wave controller/hub manual and re-try. 4. Please see section 4.4 on how to perform a local device reset if multiple remove attempts fail.

5

Factory Reset

To perform a local device reset, lightly press and hold the push button on the Swidget Z-Wave Insert for approximately 20 seconds until the LED turns SOLID RED, and then release. • After 10 seconds the LED will illuminate SOLID BLUE; indicating user is passing through network add/remove period. • After 15 seconds elapsed hold time, the LED will turn off • After 20 seconds elapsed hold time, the LED will turn SOLID RED; indicating that the user has entered the device reset period. Releasing the button during this period triggers the Factory Default Local Reset operations. When the Reset operation is in progress, the LED will progress from green to blue to red repeatedly until the reset process is complete, after which the LED will be turned OFF. If the user continues to hold the button, after 25 seconds elapse, the user will leave the device reset period, the LED will turn OFF, and no actions will be taken when the button is released. NOTE: The local reset procedure should only be used when the original controller is inoperable or has been replaced, or if Network Add or Network Remove operations have failed after a few attempts. Resetting to factory default settings will, reset the Swidget Z-Wave 500 Series Insert network parameters to the default removed state, and delete the Lifeline Association if it exists.

Electric meter

Import

Electric Meter Consumption