COMMAND_CLASS_POWERLEVEL

Powerlevel

0x73

1

COMMAND_CLASS_BATTERY

Battery

0x80

1

COMMAND_CLASS_CONFIGURATION

Configuration

0x70

1

COMMAND_CLASS_SENSOR_BINARY_V2

Sensor Binary V2

0x30

2

COMMAND_CLASS_VERSION_V2

Version V2

0x86

2

COMMAND_CLASS_WAKE_UP_V2

Wake Up V2

0x84

2

COMMAND_CLASS_DEVICE_RESET_LOCALLY

Device Reset Locally

0x5A

1

COMMAND_CLASS_ZWAVEPLUS_INFO_V2

Z-Wave Plus Info V2

0x5E

2

COMMAND_CLASS_ASSOCIATION_V2

Association V2

0x85

2

COMMAND_CLASS_ASSOCIATION_GRP_INFO

Association Group Info

0x59

1

COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

Manufacturer Specific V2

0x72

2

COMMAND_CLASS_NOTIFICATION_V4

Notification V4

0x71

4

COMMAND_CLASS_BASIC

Basic

0x20

1

Manual_Primary_Lang

Product or Owner's Manual

Sensors

Color

Battery Type

Battery Quantity

1

5

0

Lifeline communication of water leak detection to Z-Wave controller. Supported command classes: NOTIFICATION_REPORT_V4 BATTERY_REPORT SENSOR_BINARY_REPORT_V2 DEVICE_RESET_LOCALLY_NOTIFICATION

2

5

0

Control command communication to associated Z-Wave devices in the network. Use parameter 7 to configure this group’s settings. Supported command classes: BASIC_SET

3

5

0

Notifications to Z-Wave devices associated in this group. Supported command classes: NOTIFICATION_REPORT_V4

4

5

0

Notifications to Z-Wave devices associated in this group. Supported command classes: SENSOR_BINARY_REPORT_V2

3

Audio Alarm: First Beep Duration

Adjust the duration of the initial sound the alarm will produce after a leak is detected.

0

1

0

0

60

5

Enable / Disable Audio Alarm

Enable or disable the audio alarm by adjusting these parameter settings. The visual alarm will NOT be disabled and the LED indicator will always light up each time water is detected.

0

1

0

0

1

7

Trigger Action

You can choose if your Water Sensor turns an associated device on or off when sending the basic set command. Use value 0 to turn the associated device OFF and value 255 to turn it ON. Adjust brightness level for a Z-Wave dimmer (Multilevel switch) by putting in any value between 1 and 99.

0

1

0

0

255

1

Total Alarm Duration

Use this parameter to set the total duration of audio and visual alarm each time water is detected. If the value is set to 0, the alarm will continue until water is no longer detected. Use parameters 2 – 4 to customize the alarm.

0

1

0

0

120

2

Audio Alarm: Beep Interval

Set the beeping frequency for the sensor’s audio alarm. The interval between beeps can be as low as 1 minute.

0

1

0

0

1

4

Audio Alarm: Beep Duration

Adjust the duration of the beeps the alarm will sound after a leak is detected and the first “long” beep is produced.

0

1

0

0

5

6

Enable / Disable Water Detection

Enable or disable water detection for the sensor by adjusting these parameter settings.

0

1

0

0

1

2

Exclusion

1. Make sure the Water Sensor is powered on and located within direct range of your Z-Wave gateway controller 2. Put your Z-Wave controller in exclusion mode 3. Press and release the Z-Wave button 3 TIMES quickly. The LED indicator will flash quickly 4. The Water Sensor should disappear from your controller's device list If the first attempt is unsuccessful, please repeat the process following all steps carefully.

1

Inclusion

1. Bring the Water Sensor within direct range of your controller 2. Carefully remove the cover from the sensor 3. Remove the plastic pull-tab from the battery slot. The LED indicator will blink slowly 5 times 4. Put your Z-Wave controller into inclusion mode 5. Press and release the Z-Wave button on the Water Sensor 3 TIMES quickly. The LED indicator will flash quickly 6. A new water (leak) sensor will appear on your controller's device list Troubleshooting Tips If you are unable to include the Z-Wave Water Sensor to your controller, try one of the following: - Bring the sensor closer to your hub or use a hand-held secondary controller to perform inclusion - Once in inclusion mode, press and release the Z-Wave button quickly 6-7 TIMES to ensure the command has gone through - Put your controller in EXCLUSION mode. Press and release the Z-Wave button quickly 3 TIMES, and then try adding the sensor to your network again - You may need to change the device type manually if the sensor is not recognized correctly (email us for more info: ask@getzooz.com)

5

Factory Reset

When your network’s primary controller is missing or otherwise inoperable, you may need to reset the device to factory settings manually. To complete the process, make sure the Water Sensor is powered on, then PRESS AND HOLD the Z-Wave button for AT LEAST 10 SECONDS until the LED indicator flashes ONCE. Release the button. NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.

4

Device Wake-Up

If you change settings and parameters for the sensor, you may need to wake it up manually for the changes to be recorded. Press and release the Z-Wave button THREE TIMES to wake the device up. The LED indicator will flash ONCE. The sensor’s wake-up interval is set to 12 hours by default to save battery life. Though not recommended, you can change the wake-up interval using your controller’s advanced settings if available. Minimum value: 300s (5 minutes), maximum value: 16,777,200s (around 194 days). Accepted values need to match minute intervals, so 300, 360, 420, etc.

Moisture