Heatit Z-TRM6 – Z-Wave Alliance Product Catalog

Back to Listing

Product Recognition

Certification Number

ZC14-23080311

Name

Heatit Z-TRM6

Short Description

Long Description

Heatit Z-TRM6 is an electronic thermostat designed for electrical heating. The thermostat can be controlled through your Z-Wave™ network or via the buttons on the front. The thermostat has a user friendly interface. Heatit Z-TRM6 has 3 modes; Heat - Cool and Eco. The thermostat fits in standard European junction boxes and may be used with most System 55 frames. It has a sturdy metal frame for secure fastening on the junction box. The thermostat has one built-in room temperature sensor. Two additional external temperature sensors may also be connected. Heatit Z-TRM6 has active power metering and it gives you real time information about your power consumption. It also allows you to set the power metering value manually in case of connection with a contactor. The thermostat can be set up with multiple associations and can be used as a master thermostat. It can also control external relays and wall plugs.

Brand

Heatit

Product Identifier

Z-TRM6

Product Line

Thermostat

OEM Version

HW: 01 FW: 01.00:02.05

Hardware Platform

EFR32ZG23A

Z-Wave Version

7.18.1

Library Type

END_NODE_ENHANCED_232

Device Type

Thermostat DT

Role Type

ROLE_TYPE_END_NODE_ALWAYS_ON

Manufacturer ID

0x019B

Product Type ID

0x0030

Product ID

0x3001

User Icon

0x1201

Installer Icon

0x1200

Frequency Plans

EU: 869.85MHz, 868.40MHz

Categories

Thermostats

Countries / Regions

European Union

Supported Command Classes

S2 Classes

S2_AUTHENTICATED, S2_UNAUTHENTICATED

Documents

Features

Association Groups

Configuration Parameters

Texts

ID	Description	Value
8	Where to find S2 DSK on product	The QR-Code is needed when including a device using S2 security or SmartStart. The DSK can be found in the QR-Code and is located; • On the product. • In the Quick Guide. • On the packaging box/gift box.
5	Factory Reset Procedure	Enter the menu by holding the Center button for about 5 seconds, navigate in the menu with the ”+” button til you see FACT. Press the Center button until you see “-- --” blinking in the display, then hold for about 5 seconds to perform a reset. You may also initiate a reset by holding the Right and Center buttons for 60 seconds. When either of these procedures has been performed, the thermostat will perform a complete factory reset. The device will display “RES” for 5 seconds while performing a factory reset. When “RES” is no longer displayed, the thermostat has been reset. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
1	Classic Inclusion	Add The primary controller/gateway has a mode for adding devices. Please refer to your primary controller manual on how to set the primary controller in add mode. The device may only be added to the network if the primary controller is in add mode. An always listening node must be powered continuously and reside in a fixed position in the installation to secure the routing table. Adding the device within a 2 meter range from the gateway can minimize faults during the Interview process. Standard (Manual) Add mode is indicated on the device by rotating LED segments on the display. It indicates this for 90 seconds until a timeout occurs, or until the device has been added to the network. Configuration mode can also be cancelled by performing the same procedure used for starting Configuration mode. 1. Hold the Center button for 5 seconds. The display will show “OFF”. 2. Press the ”+” button once to see “CON” in the display. 3. Start the add device process in your primary controller. 4. Start the configuration mode on the thermostat by holding the Center button for approximately 2 seconds. The device is now ready for use with default settings. If inclusion fails, please perform a ”remove device” process and try again. If inclusion fails again, please see “Factory reset”.
2	Classic Exclusion	Remove The primary controller/gateway has a mode for removing devices. Please refer to your primary controller manual on how to set the primary controller in remove mode. The device may only be removed from the network if the primary controller is in remove mode. When the device is removed from the network, it will NOT revert to factory settings. Standard (Manual) Remove mode is indicated on the device by rotating LED segments on the display. It indicates this for 90 seconds until a timeout occurs, or until the device has been removed from the network. Configuration mode can also be cancelled by performing the same procedure used for starting Configuration mode. 1. Hold the Center button for 5 seconds. The display will show “OFF”. 2. Press the ”+” button once to see “CON” in the display. 3. Start the remove device process in your primary controller. 4. Start the configuration mode on the thermostat by holding the Center button for approximately 2 seconds. NB! When the device is removed from the gateway, the parameters are not reset. To reset the parameters, see Chapter ”Factory reset”.

Supported / Controlled Meter Types

Supported Notification Types

Supported Multilevel Sensors

Supports NWI

Yes

Supports Explorer Frames

Yes

Supports SmartStart

Yes

Radio Range Z-Wave (m)